Acura CSX. Manual — part 465
01
SNR9A00J18500024101KBAT00
20-170
Exterior Trim
Emblem/Sticker Replacement
FRONT ’’A’’ EMBLEM
REAR ’’A’’ EMBLEM
CSX EMBLEM
FRONT GRILLE BASE
REAR ’’A’’ EMBLEM
ADHESIVE
TAPE
TRUNK LID
CLIP
CSX EMBLEM
Edge of the trunk lid
20 (0.79)
ACURA EMBLEM
SCREWS
33
(1.3)
24
(0.94)
55
(2.17)
Edge of the inner taillight
Edge of the trunk lid
ACURA EMBLEM
TYPE-S EMBLEM
(For some models)
Unit: mm (in.)
Adhesive tape: Thickness 0.8 mm (0.03 in.)
FRONT ’’A’’ EMBLEM
Edge of the trunk lid
Edge of the inner taillight
104.5
(4.12)
21 (0.83)
17 (0.67)
22 (0.87)
CSX EMBLEM
TYPE-S EMBLEM
(For some models)
NOTE: When removing the emblems, take care not to scratch the body.
1. To remove the front ‘‘A’’ emblem, remove the front grille (see page 20-160).
2. Clean the body surface with a shop towel dampened in isopropyl alcohol. After cleaning, keep oil, grease, and
water from getting on the surface.
3. Apply the emblem where shown.
4. After installing the front ‘‘A’’ emblem, reinstall the front grille.
08/08/21 15:05:05 61SNR030_200_0172
01
SNR9A00J18526234602KBAT00
20-171
Fenderwell
Front Inner Fender Replacement
Fastener Locations
: Screw, 3
B
: Clip, 2
E, H
: Clip, 1
G
: Clip, 8
I
: Clip, 3
J
E
K
L
L
L
L
A
F
G
D
H
A
I
I
I
J
J
J
B
B
B
I
I
I
I
I
C
NOTE: Take care not to scratch the body.
1. Remove the front inner fender (A).
–1 On the back of the wheel arch, remove the screws (B), and remove the front splash guard (C).
–2 From under the front bumper (D), remove the clips (E) securing the splash shield (F) and the front inner fender
to the front bumper.
–3 From the wheel arch, remove the clips (G, H, I, J) securing the front inner fender (and splash shield) to the
body.
–4 Release the hook (K) of the splash shield, then remove the front inner fender.
NOTE: To release the clips E, H and G, pry up on the center pin at the notch (L).
2. Install the inner fender in the reverse order of removal, and note these items:
• If the clips are damaged or stress-whitened, replace them with new ones.
• Push the clips and the hooks into place securely.
08/08/21 15:05:06 61SNR030_200_0173
01
SNR9A00J18500056118KBAT00
20-172
Fenderwell
Splash Shield Replacement
Fastener Locations
: Clip, 6
B, E
: Clip, 6
F, G
A
B
C
D
E
F
G
H
I
I
I
I
E
F
F
F
B
B
B
G
C
NOTE: Take care not to scratch the body.
1. Remove the splash shield (A).
–1 Remove the clips (B) that secure the front inner fender (C) and the front splash shield to the body.
–2 From under the front bumper (D), remove the clips (E, F).
–3 From under the body, remove the clips (G).
–4 Release the hooks (H) of the front splash shield, then pull the splash shield out.
NOTE: To release the clips B, E, F and G, pry up on the center pin at the notch (I).
2. Install the splash shield in the reverse order of removal, and note these items:
• If the clips are damaged or stress-whitened, replace them with new ones.
• Push the clips and the hooks into place securely.
08/08/21 15:05:06 61SNR030_200_0174
01
02
03
SNR9A00J18526226956KBAT00
20-173
Front Fender Fairing Replacement
Fastener Locations
: Clip, 2
A
B
A
1. Remove the front inner fender as needed (see page
20-171).
2. From the wheel arch, remove the clips.
3. Open the front door. Detach the hooks (A) securing
the front fender fairing (B).
4. Remove the front fender fairing (A).
5. Install the fender fairing in the reverse order of
removal, and note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clips and the hooks into place securely.
08/08/21 15:05:07 61SNR030_200_0175
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст