Acura CSX. Manual — part 460
02
03
01
SNR9A00J18533232201KBAT00
20-153
20-153
Hood Seal Replacement
Fastener Locations
: Clip, 7
A
B
B
6. Check that the hood opens properly and closes
securely.
7. Apply touch-up paint to the hinge mounting bolts
and around the hinges, and let the paint dry.
8. Apply multipurpose grease to the hood latch and
hood hinges as indicated by the arrows.
9. Reinstall all of the removed parts.
1. Detach the clips with a clip remover, then remove
the hood seal (A) and hood corner seals (B). Take
care not to scratch the hood.
2. Install the seals in the reverse order of removal,
and if the clips are damaged or stress-whitened,
replace them with new ones.
08/08/21 15:04:56 61SNR030_200_0155
02
03
01
SNR9A00J18533232201KBAT00
20-153
20-153
Hood Seal Replacement
Fastener Locations
: Clip, 7
A
B
B
6. Check that the hood opens properly and closes
securely.
7. Apply touch-up paint to the hinge mounting bolts
and around the hinges, and let the paint dry.
8. Apply multipurpose grease to the hood latch and
hood hinges as indicated by the arrows.
9. Reinstall all of the removed parts.
1. Detach the clips with a clip remover, then remove
the hood seal (A) and hood corner seals (B). Take
care not to scratch the hood.
2. Install the seals in the reverse order of removal,
and if the clips are damaged or stress-whitened,
replace them with new ones.
08/08/21 15:04:56 61SNR030_200_0155
01
SNR9A00J18533231701KBAT00
20-154
Hood
Hood Insulator Replacement
Fastener Locations
: Clip, 7
A
B
1. Detach the clips with a clip remover. Release the
hooks (A), then remove the hood insulator (B). Take
care not to scratch the hood.
2. Install the insulator in the reverse order of removal,
and note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clips and the hooks into place securely.
08/08/21 15:04:57 61SNR030_200_0156
01
SNR9A00J18573500000MBAT00
20-155
Trunk Lid
Trunk Lid Adjustment
A
B
C
D
G
H
E
6 x 1.0 mm
18 N·m
(1.8 kgf·m, 13 lbf·ft)
E
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
H
F
F
1. Remove the rear shelf (see page 20-78).
2. Pry up on the notch (A) to release the rear hooks (B) and pivot the striker trim cap (C) on the front hooks (D), then
remove the cap. Slightly loosen each bolt (E).
3. Adjust the trunk lid alignment in the following sequence:
• Adjust the trunk lid hinges (F) right and left, as well as forward and rearward, by using the elongated holes. Take
care not to hit the rear window when loosening the bolts.
• Turn the trunk lid edge cushions (G), in or out as necessary, to make the trunk lid fit flush with the body at the
rear and side edges.
• Adjust the fit between the trunk lid and the trunk lid opening by moving the striker (H).
4. Tighten the bolts to the specified torque.
5. Make sure the trunk lid opens properly and locks securely.
6. Reinstall all removed parts.
08/08/21 15:04:57 61SNR030_200_0157
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст