Acura CSX. Manual — part 459
01
02
03
SNR9A00J18513415012KDAT00
20-149
Rear Bumper Removal/Installation
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
C
D
E
C
B
D
A
C
C
C
C
Fastener Locations
: Clip, 2
A
: Screw, 2
B
: Bolt, 2
D
: Screw, 6
C
A
B
C
B
A
B
C
NOTE:
• Have an assistant help you when removing and
installing the rear bumper.
• Take care not to scratch the rear bumper or the body.
• Put on gloves to protect your hands.
1. Remove the clips (A), screws (B, C), and bolts (D)
securing the rear bumper (E).
2. Pull on the rear bumper (A) at the wheel arch areas
to release it from the hooks (B) on the side spacers
(C).
3. With the help of an assistant, while pulling the
wheel arch portion away from the side spacer (A),
pull the rear bumper to release the bumper from
the hooks (B) on the side bracket (C).
08/08/21 15:04:55 61SNR030_200_0151
04
05
20-150
Bumpers
A
B
C
A
B
C
B
4. With the help of an assistant, pull the rear bumper
(A) to release the bumper from the hooks (B) on the
upper bracket (C).
5. Release the hooks (A), then remove the rear
bumper absorber (B) from the rear bumper beam
(C).
6. Install the bumper in the reverse order of removal,
and note these items:
• Make sure the rear bumper engages the hooks
(of both the side bracket and side spacers) on
each side securely.
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clips and the hooks into place securely.
08/08/21 15:04:55 61SNR030_200_0152
01
SNR9A00J18513415020KBAT00
20-151
Rear Bumper Lower Cover Replacement
Fastener Locations
: Clip, 2
A
B
C
D
D
NOTE: Take care not to scratch the rear bumper.
1. Remove the rear bumper (see page 20-149).
2. Release the clips and the tabs (A), then remove the
rear bumper lower cover (B) from the rear bumper
(C).
NOTE: To remove the clips, pry the inner pin up at
the edge near the line (D) on its head.
3. Install the cover in the reverse order of removal,
and note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clips and the tabs into place securely.
08/08/21 15:04:55 61SNR030_200_0153
01
SNR9A00J18533200000MBAT00
20-152
Hood
Hood Adjustment
B
C
D
E
A
6 x 1.0 mm
18 N·m
(1.8 kgf·m, 13 lbf·ft)
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
D
1. Remove these items:
• Front fender trim (see page 20-162)
• Front grille cover (see page 20-163)
• Cowl covers (see page 20-163)
2. Slightly loosen each bolt (A).
3. Adjust the hood alignment in this sequence:
• Adjust the hood right and left, as well as forward and rearward, by using the elongated holes in the hood
hinges (B).
• Turn the hood edge cushions (C), as necessary, to make the hood fit flush with the body at the front and side
edges.
4. Adjust the hood latch (D) to obtain the proper position at the forward edge, and move the hood latch right or left
until the striker (E) is centered in the hood latch.
5. Tighten the bolts to the specified torque.
08/08/21 15:04:56 61SNR030_200_0154
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст