Acura CSX. Manual — part 424
01
04
05
*01
20-20
Doors
A
B
C
Fastener Locations
: Bolt, 2
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
B
C
A
A
A
B
A
B
A
7. Disconnect the outer handle rod (A) with a clip
remover (B) from the outer handle (C).
8. Remove the maintenance seal (A). Remove the
bolts securing the outer handle protector (B), then
remove the protector by releasing the hook (C).
9. While pulling the outer handle (A), remove the
handle from the holes in the door panel. Take care
not to scratch the door.
10. Remove the rod fastener (A) from the outer handle
(B), then replace it with a new one.
Replace.
08/08/21 14:59:07 61SNR030_200_0022
01
SNR9A00J16166220801KBAT00
20-21
20-21
Rear Door Latch Replacement
Fastener Locations
: Screw, 3
A
: Screw, 1
B
A
A
A
6 x 1.0 mm
6 N·m
(0.6 kgf·m, 4 lbf·ft)
6 x 1.0 mm
6 N·m
(0.6 kgf·m, 4 lbf·ft)
C
B
11. Install the handle in the reverse order of removal,
and note these items:
• Make sure the door locks and opens properly.
• When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
• Check for water leaks (see step 9 on page 20-29).
NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Remove the plastic cover, as needed (see step 4 on
page 20-19).
4. Remove the screws (A, B) securing the latch (C),
then lower it.
5. Detach the rod fastener (see step 6 on page 20-19).
6. Disconnect the outer handle rod from the outer
handle (see step 7 on page 20-20).
08/08/21 14:59:07 61SNR030_200_0023
01
SNR9A00J16166220801KBAT00
20-21
20-21
Rear Door Latch Replacement
Fastener Locations
: Screw, 3
A
: Screw, 1
B
A
A
A
6 x 1.0 mm
6 N·m
(0.6 kgf·m, 4 lbf·ft)
6 x 1.0 mm
6 N·m
(0.6 kgf·m, 4 lbf·ft)
C
B
11. Install the handle in the reverse order of removal,
and note these items:
• Make sure the door locks and opens properly.
• When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
• Check for water leaks (see step 9 on page 20-29).
NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Remove the plastic cover, as needed (see step 4 on
page 20-19).
4. Remove the screws (A, B) securing the latch (C),
then lower it.
5. Detach the rod fastener (see step 6 on page 20-19).
6. Disconnect the outer handle rod from the outer
handle (see step 7 on page 20-20).
08/08/21 14:59:07 61SNR030_200_0023
01
03
04
20-22
Doors
A
B
C
D
F
E
Fastener Location
: Screw, 1
A
B
A
A
B
C
B
7. Detach the latch cable (A) and the inner handle
cable (B) from the holder (C), then remove the latch
(D) out from between the rear lower channel (E)
and the door. Take care not to bend the outer
handle rod (F), the latch cable, or the inner handle
cable.
8. Remove the screw, then remove the latch protector
(A) by releasing the hook (B).
9. Detach the latch cable (A) and the inner handle
cable (B) from the latch (C).
10. Install the latch in the reverse order of removal, and
note these items:
• Make sure the connector is plugged in properly,
and each rod is connected securely.
• Make sure the door locks and opens properly.
08/08/21 14:59:07 61SNR030_200_0024
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст