Acura CSX. Manual — part 425
05
06
07
SNR9A00J54400020371KBAT50
20-23
Rear Door Glass and Regulator Replacement
A
B
C
F
G
H
E
C
E
D
Fastener Locations
: Bolt, 2
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
B
A
C
Fastener Locations
: Bolt, 1
A
: Screw, 1
D
4 x 0.7 mm
4 N·m
(0.4 kgf·m, 3 lbf·ft)
6 x 1.0 mm
8 N·m
(0.8 kgf·m, 6 lbf·ft)
A
B
C
D
NOTE: Put on gloves to protect your hands.
1. Remove the door panel (see page 20-17).
2. Detach the harness clip (A), and disconnect the
power door lock actuator connector (B). Remove
the plug caps (C).
3. Pass the cable (D) and the harnesses (E) through
the holes (F) and slit (G) in the plastic cover (H),
then remove it.
4. Carefully move the glass (A) until you can see the
bolts, then remove them. Release the glass from
the holder (B), then remove it from the regulator (C),
and carefully lower the glass. Take care not to drop
the glass inside the door.
5. Remove the bolt (A) from the rear lower channel (B).
Pull the glass run channel (C) away as needed, and
remove the screw (D).
08/08/21 14:59:08 61SNR030_200_0025
08
09
10
11
20-24
Doors
A
B
C
D
E
B
A
B
A
A
A
B
B
A
6. Pull the glass run channel (A) away as needed. Pull
the rear lower channel (B) forward from the quarter
glass seal (C) then release the upper hook (D) from
the door. Remove the rear lower channel from the
rear door glass (E), then pull the channel up to
remove it.
7. Remove the rear lower channel (A) from the glass
run channel (B).
8. Carefully remove the glass (A) out through the
window slot. Take care not to drop the glass inside
the door.
9. Remove the quarter glass (A). Take care not to
damage the outer weatherstrip (B).
08/08/21 14:59:09 61SNR030_200_0026
12
13
20-25
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
(Black)
Fastener Locations
: Bolt, 4
C
: Bolt, 1
D
(Gold)
C
C
C
A
B
C
D
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
A
10. Disconnect the connector (A) from the regulator (B).
11. Remove the bolts (C), and loosen the bolt (D), then
remove the regulator through the hole in the door.
12. Grease all the sliding surfaces of the regulator (A)
where shown.
13. Install the glass and regulator in the reverse order
of removal, and note these items:
• Roll the glass up and down to verify if it moves
freely without binding.
• Make sure that there is no clearance between the
glass and glass run channel when the glass is
closed.
• Adjust the position of the glass as necessary
(see page 20-28).
• When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
• Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:09 61SNR030_200_0027
01
02
03
SNR9A00J16166220361KBAT10
20-26
Doors
Rear Door Glass Outer Weatherstrip Replacement
A
B
A
A
B
NOTE:
• Put on gloves to protect your hands.
• Take care not to scratch the door.
1. Remove these items:
• Door panel (see page 20-17)
• Plastic cover (see step 4 on page 20-19)
• Rear door glass (see page 20-23)
• Quarter glass (see step 9 on page 20-24)
2. Release the front hook (A) from inside of the door,
then pull up the front portion of the rear door glass
outer weatherstrip (B).
3. Starting at the front, slowly pull up the rear door
glass outer weatherstrip (A).
4. Push the rear hook (A) out from inside of the door,
then remove the rear door glass outer weatherstrip
(B).
5. Push the clip portions of the rear door glass outer
weatherstrip into place securely.
08/08/21 14:59:10 61SNR030_200_0028
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст