Acura CSX. Manual — part 322
02
03
04
’06 Model
’07-09 Models
14-360
A/T Differential
A
B
C
D
A
B
C
D
07749-0010000
07746-0010600
3. Install the 76 mm thrust shim (A), the 76.2 mm
thrust washer (B), and the carrier bearing outer
race (C) in the transmission housing (D).
NOTE:
For ’07-09 models: Be sure to install the 76.2 mm
thrust washer with the ‘‘41382 RKY’’ mark facing
downward.
4. Install the outer race securely in the housing so
there is no clearance between the outer race, the
thrust washer, the thrust shim, and the
transmission housing using the driver and the
72 x 75 mm attachment.
08/08/21 14:53:04 61SNR030_140_0362
05
06
01
SNR9AA1E10411619611MAAT00
Special Tools Required
’06 Model
14-361
14-361
Carrier Bearing Preload Inspection
A
B
C
07749-0010000
07NAD-PX40100
A
B
C
D
E
5. Install the 80 mm thrust washer (A) and the carrier
bearing outer race (B) in the torque converter
housing (C).
6. Install the carrier bearing outer race securely in the
torque converter housing so there is no clearance
between the carrier bearing outer race, the 80 mm
thrust washer, and the torque converter housing
using the driver and the 78 x 80 mm attachment.
• Driver 07749-0010000
• Attachment, 72 x 75 mm 07746-0010600
• Preload inspection tool 07HAJ-PK40201
NOTE:
• Replace the carrier bearing with a new one whenever
the carrier bearing outer race is replaced. The carrier
bearing and the carrier bearing outer race should be
replaced as a set.
• Do not use the 76 mm thrust shim on the torque
converter housing.
• Adjust the carrier bearing preload, when replacing
the transmission housing, the torque converter
housing, the differential carrier, the carrier bearing,
the carrier bearing outer race, or the 76 mm thrust
shim.
1. Remove the carrier bearing outer race (A), the
76.2 mm thrust washer (B), and the 76 mm thrust
shim (C) from the transmission housing (D) by
heating the housing to about 100 °C (212 °F) with a
heat gun (E). Do not heat the housing more than
100 °C (212 °F).
08/08/21 14:53:05 61SNR030_140_0363
05
06
01
SNR9AA1E10411619611MAAT00
Special Tools Required
’06 Model
14-361
14-361
Carrier Bearing Preload Inspection
A
B
C
07749-0010000
07NAD-PX40100
A
B
C
D
E
5. Install the 80 mm thrust washer (A) and the carrier
bearing outer race (B) in the torque converter
housing (C).
6. Install the carrier bearing outer race securely in the
torque converter housing so there is no clearance
between the carrier bearing outer race, the 80 mm
thrust washer, and the torque converter housing
using the driver and the 78 x 80 mm attachment.
• Driver 07749-0010000
• Attachment, 72 x 75 mm 07746-0010600
• Preload inspection tool 07HAJ-PK40201
NOTE:
• Replace the carrier bearing with a new one whenever
the carrier bearing outer race is replaced. The carrier
bearing and the carrier bearing outer race should be
replaced as a set.
• Do not use the 76 mm thrust shim on the torque
converter housing.
• Adjust the carrier bearing preload, when replacing
the transmission housing, the torque converter
housing, the differential carrier, the carrier bearing,
the carrier bearing outer race, or the 76 mm thrust
shim.
1. Remove the carrier bearing outer race (A), the
76.2 mm thrust washer (B), and the 76 mm thrust
shim (C) from the transmission housing (D) by
heating the housing to about 100 °C (212 °F) with a
heat gun (E). Do not heat the housing more than
100 °C (212 °F).
08/08/21 14:53:05 61SNR030_140_0363
01
02
03
’07-09 Models
’06 Model
’07-09 Models
14-362
A/T Differential
A
D
E
B
C
A
C
D
B
A
B
C
D
2. Install the 76 mm thrust shim (A) in the
transmission housing (B).
If you replace the 76 mm thrust shim with a new
one, use the same thickness shim as the old one.
3. Install the 76.2 mm thrust washer (C), and the
carrier bearing outer race (D) in the transmission
housing.
NOTE:
For ’07-09 models: Be sure to install the 76.2 mm
thrust washer with the ‘‘41382 RKY’’ mark facing
downward.
08/08/21 14:53:06 61SNR030_140_0364
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст