Acura CSX. Manual — part 320

０８

＊０５

＊０６

０５

14-352

Transmission End Cover

B

A

E
8 x 1.25 mm
28 N·m
(2.9 kgf·m,
21 lbf·ft)

D

E

B

F
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)

6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)

C

A

G

A

A

B

C

D

19. Install the ATF feed pipe (A) into the idler gear shaft,

and install the ATF lubrication pipe (B) into the
transmission housing.

20. Install a new gasket (A) on the transmission

housing, and install the two dowel pins (B) and new
O-rings (C) over the top of the ATF feed pipes.

21. Install the end cover (D), and tighten the three

special bolts (E) and the 6 x 1.0 mm bolts (F)
(12 bolts).

22. Install the harness clamp bracket (G) on the end

cover.

23. Set the selector control shaft (A) to the N position

by turning the control lever on the torque converter
side.

NOTE: Do not squeeze the end of the selector
control shaft tips together when turning the
selector control shaft. If the tips are squeezed
together it will cause a faulty shift position signal or
position due to the play between the selector
control shaft and the transmission range switch.

24. Align the cutouts (A) on the rotary-frame with the

neutral positioning cutouts (B) on the transmission
range switch (C), then put a 2.0 mm (0.08 in.) feeler
gauge blade (D) in the cutouts to hold in the N
position.

NOTE: Be sure to use a 2.0 mm (0.08 in.) blade or
equivalent to hold the transmission range switch in
the N position.

Replace.

Replace.

08/08/21 14:52:37 61SNR030_140_0354

１２

１３

１４

＊０７

14-353

A

B

C

6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)

6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)

A

D

B

C

E

D

B

C

A

6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)

25. Install the transmission range switch (A) gently on

the selector control shaft (B) while holding it in the
N position using the 2.0 mm (0.08 in.) blade (C).

26. Tighten the bolts on the transmission range switch

while you continue to hold it in the N position. Do
not move the transmission range switch when
tightening the bolts. Remove the feeler gauge.

27. Connect the transmission range switch connector

(A) securely, then install the harness clamps (B) on
the clamp bracket (C).

28. Install the transmission range switch cover (D).

29. Install a new gasket (B) on the transmission

housing, and install the ATF pipe (C) and the ATF
joint pipes (D).

NOTE: Be sure to install a new gasket with the blue
side toward the transmission housing.

30. Install new O-rings (E) over the ATF joint pipes, and

install A/T clutch pressure control solenoid valve A.

Replace.

08/08/21 14:52:38 61SNR030_140_0355

０６

１７

１８

14-354

Transmission End Cover

A

D

E

B

C

F

6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)

F

B
28 N·m (2.9 kgf·m, 21 lbf·ft)

E
28 N·m (2.9 kgf·m, 21 lbf·ft)

C

C

A

D

F

F

A

B

31. Install a new gasket (A) and the ATF joint pipes (D)

on the transmission housing, and install new
O-rings (E) over the ATF joint pipes.

NOTE: Be sure to install a new gasket with the blue
side toward the transmission housing.

32. Install A/T clutch pressure control solenoid valves B

and C, and the harness clamp brackets (F).

33. Install the ATF cooler inlet line (A) with the banjo

bolt (B) and new sealing washers (C).

34. Install the ATF cooler outlet line (D) with the banjo

bolt (E) and new sealing washers (F).

35. Install the breather cap (A) on the breather pipe (B).

36. Install the ATF dipstick.

08/08/21 14:52:39 61SNR030_140_0356

＊０１

ＳＮＲ９ＡＡＡＥ１０４１１６０００００ＤＡＡＴ００

＊０１

ＳＮＲ９ＡＡＧＥ１０４１１６０００００ＤＡＡＴ０２

’06 Model

’07-09 Models

14-355

14-355

A/T Differential

Component Location Index

THRUST SHIM, 76 mm

THRUST WASHER, 80 mm

BEARING OUTER RACE

CARRIER BEARING

CARRIER BEARING

BEARING OUTER RACE

THRUST WASHER, 76.2 mm

FINAL DRIVEN GEAR

DIFFERENTIAL CARRIER

THRUST SHIM, 76 mm

THRUST WASHER, 80 mm

BEARING OUTER RACE

CARRIER BEARING

CARRIER BEARING

BEARING OUTER RACE

THRUST WASHER, 76.2 mm

FINAL DRIVEN GEAR

DIFFERENTIAL CARRIER

Preload Inspection,

page 14-361

Replacement,

page 14-359

Replacement,

page 14-357

Replacement,

page 14-357

Replacement,

page 14-359

Replacement,

page 14-356

Backlash Inspection,

page 14-356

Replacement,

page 14-356

Preload Inspection,

page 14-361

Replacement,

page 14-359

Replacement,

page 14-357

Replacement,

page 14-357

Replacement,

page 14-359

Replacement,

page 14-356

Backlash Inspection,

page 14-356

Replacement,

page 14-356

08/08/21 14:52:43 61SNR030_140_0357