Acura CSX. Manual — part 443
01
02
03
SNR9A00J26216516401KDAT00
Special Tools Required
20-92
Consoles
Center Console Removal/Installation
A
B
C
Fastener Locations
: Clip, 4
A
Fastener Locations
: Clip, 3
B
: Clip, 2
C
C
B
B
B
C
A
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
• Take care not to scratch the front seat, dashboard,
and related parts.
1. Remove the passenger’s dashboard undercover
(see page 20-104).
2. M/T model: Lower the shift lever boot (A) to release
the hooks (B) from the boot, then remove the shift
knob (C).
3. Detach the clips by pulling the front inner panel (A)
up.
4. Gently pull out along the rear of the center console
panel (A) to release the clips (B, C).
08/08/21 15:02:47 61SNR030_200_0094
07AAC-SEPA240
04
05
01
20-93
A
B
Fastener Locations
: Bolt, 2
A
B
5 x 0.8 mm
5 N·m
(0.5 kgf·m,
4 lbf·ft)
Fastener Locations
: Bolt, 2
: Clip, 2
5 x 0.8 mm
5 N·m
(0.5 kgf·m,
4 lbf·ft)
B
A
5. Pull the center console panel (A) up and rearward
to release the tabs (B).
6. Open the armrest (A), and remove the console box
mat (B) to access and remove the bolts.
7. Remove the bolts and the clips from the front
portion of the center console. Disconnect the
console subharness connector (A), and detach the
connector clip (B).
08/08/21 15:02:48 61SNR030_200_0095
07
08
09
20-94
Consoles
A
B
C
B
A
B
A
B
C
8. Slide both front seats all the way back, and recline
the seat-back fully.
9. Slide the center console (A) rearward to release the
pins (B) from the bracket (C).
10. Lift up the rear of the console (A), and remove it
from the dashboard.
11. If equipped, disconnect the seat heater switch
connectors (B).
12. Install the console in the reverse order of removal,
and note these items:
• Make sure each connector is plugged in properly.
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clips and the hooks into place securely.
• When installing the center console panel, install
the tabs (A) into the notch (B) of the parking brake
base frame (C).
08/08/21 15:02:48 61SNR030_200_0096
*01
02
03
SNR9A00J26216516401MFAT00
Special Tools Required
20-95
Center Console Disassembly/Reassembly
Fastener Locations
: TORX Screw, 8
A
A
B
C
D
E
F
G
H
I
I
A
A
B
C
D
KTC trim tool set SOJATP2014
NOTE:
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
• Take care not to scratch the center console, the
dashboard, and related parts.
1. Remove the center console (see page 20-92).
2. Remove the center console armrest (see page
20-96).
3. Remove the screws with a TORX T20 bit, and
disconnect the console accessory power socket
connector (A).
4. Release the hooks (A) and the pins (B), then
separate the left console side panel (C), the right
console side panel (D), the console beverage holder
(E) and the console box (F). If equipped, detach the
harness clips (G), then remove the console
subharness (H) from the hooks (I).
5. Release the hooks (A, B), then separate the console
upper box (C) and the console lower box (D).
6. Assemble the console in the reverse order of
disassembly, and make sure the console
subharness connector is plugged in properly.
08/08/21 15:02:49 61SNR030_200_0097
07AAC-SEPA240
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст