Acura CSX. Manual — part 442
11
12
13
SNR9A00J26200016101KBAT00
Headliner
Grab handle
Sunvisor
Special Tools Required
20-88
20-88
Interior Trim
Carpet Replacement
A
C
H
I
C
J
K
B
B
F
D
E
G
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:
• Put on gloves to protect your hands.
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
• Take care not to damage, wrinkle, or twist the carpet.
• Be careful not to damage the dashboard or other
interior trim pieces.
1. Remove these items:
• Front seats, both sides (see page 20-118)
• Rear seat cushion (see page 20-133)
• Front door sill trim, both sides (see page 20-66)
• Rear door sill trim, both sides (see page 20-67)
• Kick panels, both sides (see step 5 on page 20-67)
• B-pillar lower trim (see page 20-72)
• Driver’s dashboard undercover (see page 20-103)
• Passenger’s dashboard undercover (see page
20-104)
• Center console (see page 20-92)
• Steering joint cover (see page 17-10)
08/08/21 15:01:42 61SNR030_200_0090
07AAC-SEPA240
*01
02
01
20-89
D
E
B
C
A
D
Fastener Locations
: Clip, 1
B
: Clip, 1
D
A
B
C
D
A
B
D
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
C
C
2. Release the hooks (A) to remove the accelerator
pedal clip (B). While pushing down the back-up
spring (C), pull back the accelerator pedal (D) to
release the hook (E).
3. Remove the footrest (A).
–1 Remove the lower clip (B) with a 6 mm
hexagon wrench, from the stud bolt (C).
–2 Remove the upper clip (D) with a flat-tip
screwdriver, from the stud bolt.
4. Disconnect the SRS unit connector (A), antenna
connector (B), and detach the wire harness clips (C).
Remove the ground bolt (D) with a TORX T30 bit.
Use a TORX T30 bit.
08/08/21 15:02:46 61SNR030_200_0091
03
04
02
06
20-90
Interior Trim
Fastener Locations
: Bolt, 2
A
: Bolt, 1
C
D
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
A
B
B
A
A
Fastener Locations
: Clip, 2
5. Remove the bolts (A, B), and detach the connector
clip (C), then remove the center pipe extension (D).
6. Remove the rear heater joint duct (A).
7. Disconnect the parking brake cables from the
equalizer (see page 19-40).
8. Remove the floor mat holders (A) from the driver’s
side.
9. Remove the clips.
08/08/21 15:02:46 61SNR030_200_0092
07
20-91
A
B
C
C
10. Release the Velcro fastener (A), then pull the carpet
(B) out from under the dashboard.
11. Pull the seat harnesses (C) out through the hole in
the carpet, then remove the carpet.
12. Install the carpet in the reverse order of removal,
and note these items:
• Take care not to damage, wrinkle or twist the
carpet.
• Make sure the seat harnesses and parking brake
cables are routed correctly.
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the Velcro fasteners and the clips into place
securely.
• Push the accelerator pedal hooks into place
securely, and verify that the pedal is properly
fastened to the floor.
08/08/21 15:02:47 61SNR030_200_0093
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст