Acura CSX. Manual — part 672
10
01
SNR9A00H46200053402KBAT00
Center anchor bolt installation
Rear Seat Belt
24-7
24-7
Rear Seat Belt Replacement
CENTER ANCHOR
CENTER ANCHOR
BOLT
TOOTHED
LOCK WASHER
SPRING WASHER
A
7/16-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)
6. Install the buckle in the reverse order of removal,
and note these items:
• Assemble the washers on the center anchor bolt
as shown.
• Apply medium strength liquid thread lock to the
center anchor bolt before reinstallation.
• Tighten the bolts by hand first, then tighten to
specification with a torque wrench.
• Make sure the seat belt switch connector and
seat belt buckle tensioner connector are plugged
in properly.
• Check for any DTCs that may have been set
during repairs, and clear them using the HDS.
• Do the battery terminal reconnection procedure
(see page 22-68).
NOTE: Check the second row seat belts for damage,
and replace them if necessary.
1. Remove the rear seat cushion (see page 20-133).
2. Remove the lower anchor bolt (A).
3. Remove these items:
• Rear seat side bolsters, both sides (see page
20-134)
• C-pillar trim, both sides (see page 20-75)
• Rear shelf (see page 20-78)
08/08/21 13:54:09 61SNR030_240_0007
10
01
SNR9A00H46200053402KBAT00
Center anchor bolt installation
Rear Seat Belt
24-7
24-7
Rear Seat Belt Replacement
CENTER ANCHOR
CENTER ANCHOR
BOLT
TOOTHED
LOCK WASHER
SPRING WASHER
A
7/16-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)
6. Install the buckle in the reverse order of removal,
and note these items:
• Assemble the washers on the center anchor bolt
as shown.
• Apply medium strength liquid thread lock to the
center anchor bolt before reinstallation.
• Tighten the bolts by hand first, then tighten to
specification with a torque wrench.
• Make sure the seat belt switch connector and
seat belt buckle tensioner connector are plugged
in properly.
• Check for any DTCs that may have been set
during repairs, and clear them using the HDS.
• Do the battery terminal reconnection procedure
(see page 22-68).
NOTE: Check the second row seat belts for damage,
and replace them if necessary.
1. Remove the rear seat cushion (see page 20-133).
2. Remove the lower anchor bolt (A).
3. Remove these items:
• Rear seat side bolsters, both sides (see page
20-134)
• C-pillar trim, both sides (see page 20-75)
• Rear shelf (see page 20-78)
08/08/21 13:54:09 61SNR030_240_0007
02
03
04
Center Seat Belt and Seat Belt Buckles
24-8
Seat Belts
B
C
A
7/16-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)
A
7/16-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)
B
C
D
E
C
A
6 x 1.0 mm
1.5 N·m
(0.15 kgf·m, 1.1 lbf·ft)
B
7/16-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)
D
4. Remove the retractor bolt (A), then remove the rear
seat belt (B) and retractor (C).
5. Install the rear seat belt and retractor in the reverse
order of removal, and note these items:
• Apply medium strength liquid thread lock to the
anchor bolts before reinstallation.
• Check that the retractor locking mechanism
functions as described (see page 24-9).
• Before installing the anchor bolt, make sure there
are no twists or kinks in the rear seat belt.
1. Remove the rear seat cushion (see page 20-133).
2. Remove the center anchor bolts (A), then remove
the right seat belt buckle (B), center seat belt buckle
(C), and left seat belt buckle (D).
3. Fold both rear seat-backs forward.
4. Remove the rear shelf (see page 20-78).
5. Remove the retractor mounting ET screw (A) and
the retractor bolt (B), then remove the rear seat belt
(C) and retractor (D).
6. Remove the rear center seat belt protector (E).
08/08/21 13:54:09 61SNR030_240_0008
02
*01
01
02
SNR9A00H46200053401MAAT00
Center anchor bolt installation
Front
Rear
Out of Vehicle
Retractor
24-9
24-9
Inspection
CENTER ANCHOR
BOLT
WASHER
TOOTHED
LOCK WASHER
CENTER ANCHOR
’06 model
CENTER ANCHOR
BOLT
WASHER
TOOTHED
LOCK WASHER
CENTER ANCHOR
’07-09 models
Left side: 10 °
Right side: 13 °
40 °
40 °
40 °
40 °
15 °
15 °
15 °
15 °
A
Inside
Front
40 °
40 °
40 °
40 °
15 °
15 °
15 °
15 °
A
Inside
Front
7. Install the seat belt and buckles in the reverse order
of removal, and note these items:
• If the threads on a retractor mounting ET screw
are worn out, use an oversized selftapping ET
screw (P/N 90133-SZ4-003) made specifically for
this application.
• Apply medium strength liquid thread lock to the
center anchor bolt before reinstallation.
• Tighten the bolt by hand first, then tighten to the
specified torque.
• Check that the retractor locking mechanism
functions as described (see page 24-9).
• Assemble the washers on the center anchor bolt
as shown.
• Before installing the center anchor bolt, make
sure there are no twists or kinks in the center belt.
• Make sure the rear center emergency locking
retractor (ELR) is pointing straight forward.
For front seat belt retractor with seat belt tensioner,
review the SRS component locations (see page 24-11)
and the precautions and procedures (see page 24-13)
before doing repairs or service.
1. Before installing the retractor, check that the seat
belt can be pulled out freely.
2. Make sure that the seat belt does not lock when the
retractor (A) is leaned slowly up to 15 ° from the
mounted position. The seat belt should lock when
the retractor is leaned over 40 °. Do not attempt to
disassemble the retractor.
08/08/21 13:54:10 61SNR030_240_0009
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст