Acura CSX. Manual — part 201
01
SNR9AA8E34150339091MFAT00
13-28
Manual Transmission
Change Lever Assembly Disassembly/Reassembly
BREATHER CAP
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 9 lbf·ft)
ROLLER
WASHER
5TH SELECT
SPRING
SELECT STOP
PLATE
SHIFT ARM
COVER
INTERLOCK
REVERSE LOCK CAM
STRIKER
8 mm SPRING WASHER
8 mm SPECIAL BOLT
31 N·m
(3.2 kgf·m, 23 lbf·ft)
DUST COVER
CHANGE LEVER
CHANGE LEVER COVER
SELECT LEVER
DUST SEAL
1ST/2ND SELECT
SPRING
SHIFT ARM
OIL SEAL
(P/N 08798-9002)
(P/N 08798-9002)
(P/N 08798-9002)
NOTE: Prior to reassembling, clean all the parts in solvent, dry them, and apply grease to the contact surfaces as
shown.
Turn toward the front of
the vehicle, then install it.
Be careful not to damage the
dust seal when installing it.
Replace.
Replace.
08/08/21 14:45:01 61SNR030_130_0030
01
02
03
04
SNR9AA8E34150354901MAAT00
−
−
−
−
−
−
−
−
Standard:
0.35
0.65 mm (0.014
0.026 in.)
Service Limit: 1.0 mm (0.039 in.)
Standard: 7.4
7.6 mm (0.29
0.30 in.)
Standard:
0.2
0.5 mm (0.008
0.020 in.)
Service Limit: 0.62 mm (0.024 in.)
Standard: 16.9
17.0 mm (0.665
0.669 in.)
13-29
Shift Fork Clearance Inspection
A
B
B
A
1. Measure the clearance between each shift fork (A)
and its matching synchro sleeve (B). If the
clearance exceeds the service limit, go to step 2.
2. Measure the thickness of the shift fork fingers.
• If the thickness is not within the standard, replace
the shift fork.
• If the thickness is within the standard, replace the
synchro sleeve and the synchro hub as a set.
• If one arm of the shift fork shows more wear than
others, the fork may be bent and needs to be
replaced.
3. Measure the clearance between the shift fork (A)
and the shift arm (B). If the clearance exceeds the
service limit, go to step 4.
4. Measure the width of the shift arm.
• If the width is not within the standard, replace the
shift arm.
• If the width is within the standard, replace the
shift fork and the reverse shift piece.
08/08/21 14:45:02 61SNR030_130_0031
*01
SNR9AA8E34150354901MFAT00
13-30
Manual Transmission
Shift Fork Disassembly/Reassembly
1ST/2ND
SHIFT FORK
5 x 25 mm SPRING PIN
PIN DRIVER, 5 mm
3RD/4TH
SHIFT FORK
5TH SHIFT FORK
REVERSE SHIFT PIECE
NOTE: Prior to reassembling, clean all the parts in solvent, dry them, and apply MTF to all contact surfaces.
Replace.
08/08/21 14:45:02 61SNR030_130_0032
*01
02
*02
SNR9AA8E34150400000MAAT10
−
−
−
−
−
−
Standard:
0.06
0.16 mm (0.002
0.006 in.)
Service Limit: 0.25 mm (0.010 in.)
Standard:
23.92
23.97 mm (0.942
0.944 in.)
Service Limit: 23.80 mm (0.937 in.)
Standard:
0.06
0.16 mm (0.002
0.006 in.)
Service Limit: 0.25 mm (0.010 in.)
13-31
Mainshaft Assembly Clearance Inspection
D
E
B
C
A
B
C
A
1. Support the bearing inner race with an appropriate
sized socket (A), and push down on the
mainshaft (B).
2. Measure the clearance between 2nd gear (C) and
3rd gear (D) with a feeler gauge (E).
• If the clearance exceeds the service limit, go to
step 3.
• If the clearance is within the service limit, go to
step 4.
3. Measure the thickness of 3rd gear.
• If the thickness is less than the service limit,
replace 3rd gear.
• If the thickness is within the service limit, replace
the 3rd/4th synchro hub and the 3rd/4th synchro
sleeve as a set.
4. Measure the clearance between 4th gear (A) and
the 4th/5th gear distance collar (B) with a dial
indicator (C).
• If the clearance exceeds the service limit, go to
step 5.
• If the clearance is within the service limit, go to
step 7.
08/08/21 14:45:02 61SNR030_130_0033
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст