Acura RSX Honda Integra. Manual — part 255
*06
13
−
−
−
−
YES
NO
YES
NO
14-145
PCM CONNECTORS
ATP D3 (RED)
LG1 (BRN/YEL)
A (31P)
C (22P)
PCM CONNECTOR C (22P)
ATP D3 (RED)
37. Shift to all positions other than D3.
38. Measure the voltage between PCM connector
terminals C9 and A9.
Go to step 43.
Go to step 39.
39. Turn the ignition switch OFF.
40. Jump the SCS line with the HDS.
41. Disconnect PCM connector C (22P).
42. Check for continuity between PCM connector
terminal C9 and body ground.
Repair short to ground in the wire between
PCM connector terminal C9 and the transmission
range switch, then go to step 49.
Update the PCM if it does not have the latest
software, or substitute a known-good PCM
(see page 14-11), then recheck. If the symptom/
indication goes away with a known-good PCM,
replace the original PCM.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Is ther e batter y voltage?
Is ther e continuity?
05/06/27 17:50:42 61S6M040_140_0146
*07
15
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
14-146
Automatic Transmission
DTC Troubleshooting (cont’d)
PCM CONNECTORS
ATP FWD (BLU/YEL)
LG1 (BRN/YEL)
A (31P)
C (22P)
PCM CONNECTOR C (22P)
ATP FWD (BLU/YEL)
43. Shift to all positions other than D and D3.
44. Measure the voltage between PCM connector
terminals C18 and A9.
Update the PCM if it does not have the latest
software, or substitute a known-good PCM
(see page 14-11), then recheck. If the symptom/
indication goes away with a known-good PCM,
replace the original PCM.
Go to step 45.
45. Turn the ignition switch OFF.
46. Jump the SCS line with the HDS.
47. Disconnect PCM connector C (22P).
48. Check for continuity between PCM connector
terminal C18 and body ground.
Repair short to ground in the wire between
PCM connector terminal C18 and the transmission
range switch, then go to step 49.
Update the PCM if it does not have the latest
software, or substitute a known-good PCM
(see page 14-11), then recheck. If the symptom/
indication goes away with a known-good PCM,
replace the original PCM.
49. Clear the DTC with the HDS.
50. Move the shift lever to each position, and monitor
the OBD status for P0705 in the DTCs/Freeze Data in
A/T Mode Menu for a pass/fail.
Troubleshooting is completed.
Return to step 1 and recheck.
Wire side of female terminals
Wire side of female terminals
Is ther e batter y voltage?
Is ther e continuity?
Does the r esult indicate a passed?
05/06/27 17:50:42 61S6M040_140_0147
S6M6APPK77100090706FAAT00
−
−
−
−
−
−
−
−
−
−
DTC P0706:
2005-2006 Models
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
14-147
Open in Transmission Range
Switch Circuit
NOTE:
• Record all freeze data and review General
Troubleshooting Information (see page 14-8) before
you troubleshoot.
• This code is caused by an electrical circuit problem
and cannot be caused by a mechanical problem in the
transmission.
1. Clear the DTC with the HDS.
2. Raise the front of the vehicle, make sure it is
securely supported, and allow the front wheels to
rotate freely.
3. Start the engine, drive the vehicle in the D position
until the vehicle speed reaches 35 mph (56 km/h),
then slow down and stop the wheels.
4. Monitor the OBD status for P0706 in the DTCs/
Freeze Data in A/T Mode Menu for a pass/fail.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the transmission range switch and PCM. If the
tester indicates NOT COMPLETED, return to step 1
and recheck.
5. Test the transmission range switch (see page
14-306).
Inspect the end of the selector control shaft
(see step 6 on page 14-308), and go to step 6.
Replace the transmission range switch, then
go to step 24.
6. Install the transmission range switch correctly, and
adjust the shift cable (see page 14-299).
7. Clear the DTC with the HDS.
8. Raise the front of the vehicle, make sure it is
securely supported, and allow the front wheels to
rotate freely.
9. Start the engine, drive the vehicle in the D position
until the vehicle speed reaches 35 mph (56 km/h),
then slow down and stop the wheels.
10. Monitor the OBD status for P0706 in the DTCs/
Freeze Data in A/T Mode Menu for a pass/fail.
Go to step 11.
The problem has been corrected. If the tester
indicates NOT COMPLETED, return to step 7 and
recheck.
11. Shift the shift lever into the D position, and verify
the ATP FWD and ATP D inputs with the HDS in the
A/T data list.
Go to step 12.
Go to step 17.
12. Shift to the D3 position, and verify the ATP FWD
and ATP D3 inputs with the HDS in the A/T date list.
Go to step 13.
Go to step 17.
13. Clear the DTC with the HDS, and turn the ignition
switch OFF.
14. Raise the front of the vehicle, make sure it is
securely supported, and allow the front wheels to
rotate freely.
15. Start the engine, drive the vehicle in the D position
until the vehicle speed reaches 35 mph (56 km/h),
then slow down and stop the wheels.
(cont’d)
Does the r esult indicate a f ailed?
Is the switch OK ?
Does the r esult indicate a f ailed?
Is the AT P F W D and AT P D ON?
Is the AT P F W D and AT P D3 ON?
05/06/27 17:50:42 61S6M040_140_0148
01
02
03
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
YES
NO
14-148
Automatic Transmission
DTC Troubleshooting (cont’d)
TRANSMISSION RANGE
SWITCH CONNECTOR
PG (BLK)
TRANSMISSION RANGE
SWITCH CONNECTOR
PG (BLK)
ATP FWD (YEL/RED)
TRANSMISSION RANGE
SWITCH CONNECTOR
PG (BLK)
ATP D (PNK)
16. Monitor the OBD status for P0706 in the DTCs/
Freeze Data in A/T Mode Menu for a pass/fail.
Go to step 17.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the transmission range switch and PCM. If the
tester indicates NOT COMPLETED, return to step 13
and recheck.
17. Turn the ignition switch OFF.
18. Disconnect the transmission range switch
connector.
19. Check for continuity between transmission range
switch connector terminal No. 10 and body ground.
Go to step 20.
Repair open in the wire between transmission
range switch connector terminal No. 10 and ground
(G101), or repair poor ground (G101), then go to
step 24.
20. Turn the ignition switch ON (II).
21. Measure the voltage between transmission range
switch connector terminals No. 5 and No. 10.
Go to step 22.
Repair open in the wire between the
transmission range switch and PCM connector
terminal C18, then go to step 24.
22. Measure the voltage between transmission range
switch connector terminals No. 8 and No. 10.
Go to step 23.
Repair open in the wire between the
transmission range switch and PCM connector
terminal C17, then go to step 24.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Does the r esult indicate a f ailed?
Is ther e continuity?
Is ther e batter y voltage?
Is ther e batter y voltage?
05/06/27 17:50:42 61S6M040_140_0149
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст