Acura RSX Honda Integra. Manual — part 166
02
03
01
02
S6M6A00A20326428001KCAT00
11-370
11-370
Fuel Supply System
Fuel Line/Quick-Connect Fitting
Removal (cont’d)
Fuel Line/Quick-Connect Fitting
Installation
A
B
A
A
B
B
A
4. Check the contact area (A) of the line (B) for dirt or
damage.
• If it is dirty, clean it.
• If it is rusty or damaged, replace the fuel pump,
fuel filter, or fuel feed line.
5. To prevent damage and keep foreign matter out,
cover the disconnected connector and line ends
with plastic bags (A).
NOTE:
• The retainer cannot be reused once it has been
removed from the line.
Replace the retainer when:
– replacing the fuel rail.
– replacing the fuel feed line.
– replacing the fuel pump.
– replacing the fuel filter.
– replacing the fuel gauge sending unit.
– replacing the EVAP purge pipe.
– replacing the EVAP canister.
– it has been removed from the line.
– it is damaged.
NOTE: Before you work on the fuel lines and fittings,
read the ‘‘Fuel Line/Quick-Connect Fitting Precautions’’
(see page 11-368).
1. Check the contact area (A) of the line (B) for dirt or
damage, and clean it if needed.
2. Insert a new retainer (A) into the connector (B) if the
retainer is damaged, or after:
• replacing the fuel rail.
• replacing the fuel feed line.
• replacing the fuel pump.
• replacing the fuel filter.
• replacing the fuel gauge sending unit.
• replacing the EVAP purge pipe.
• replacing the EVAP canister.
• removing the retainer from the line.
• Use the same manufacturer retainer and the
same size retainer when the replacing the
retainer (see page 11-368).
05/06/27 17:41:45 61S6M040_110_0370
01
03
01
02
2002-2004 models
2005-2006 models
2005-2006 models
11-371
A
A
A
A
3. Before connecting a new fuel tube/quick-connect
fitting assembly (A), remove the old retainer from
the mating line.
(cont’d)
05/06/27 17:41:46 61S6M040_110_0371
04
*01
05
*03
*02
Connection with new retainer
Connection to new fuel feed line
Reconnection to existing retainer
Reconnection to existing retainer
Connection to new fuel feed line
11-372
Fuel Supply System
Fuel Line/Quick-Connect Fitting Installation (cont’d)
C
B
A
A
C
B
C
B
A
A
B
B
A
C
4. Align the quick-connect fittings with the line (A),
and align the retainer locking tabs (B) with the
connector (C) grooves. Then press the quick-
connect fittings onto the line until both retainer tabs
lock with a clicking sound.
NOTE: If it is hard to connect, put a small amount of
new engine oil on the line end.
5. When you are reconnecting the connector with the
old retainer, make sure the connection is secure
and the tabs (A) are firmly locked into place; check
visually and also by pulling the connector (B).
When you are replacing the fuel line with a new
one, make sure you remove the ring pull (C)
upwards after you confirm the connection is secure.
NOTE: Before you remove the ring pull, make sure
the fuel line connection is secure. If the connection
is not secure, the ring pull could break when you try
to remove it.
6. Reconnect the negative cable to the battery, and
turn the ignition switch ON (II) (but do not operate
the starter motor). The fuel pump will run for about
2 seconds, and fuel pressure will rise. Repeat two
or three times, and check that there is no leakage in
the fuel supply system.
05/06/27 17:41:47 61S6M040_110_0372
01
S6M6AZFA20326428201KBAT00
01
S6M6AZHA20326428201KBAT00
2002-2004 models
2005-2006 models
11-373
11-373
Fuel Pressure Regulator Replacement
B
A
A
D
B
C
1. Remove the fuel pump (see page 11-375).
2. Remove the fuel pressure regulator (A).
3. Install the regulator in the reverse order of removal
with a new O-ring (B).
1. Remove the fuel pump (see page 11-376).
2. Remove the terminal (A) and clip (B).
3. Remove the fuel pressure regulator (C).
4. Install the regulator in the reverse order of removal
with a new O-ring (D).
05/06/27 17:41:47 61S6M040_110_0373
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст