Acura RSX Honda Integra. Manual — part 216
02
03
01
−
−
−
−
YES
NO
2002-2004 models:
2005-2006 models:
YES
NO
13-79
REVERSE LOCKOUT SOLENOID
2P CONNECTOR
RVSLCK
(GRN/WHT)
ECM CONNECTOR B (24P)
ECM CONNECTOR E (31P)
RVSLCK
(YEL/RED)
13. Connect the No. 2 terminal of the reverse lockout
solenoid 2P connector to the battery positive
terminal, and connect the No. 1 terminal to the
battery negative terminal. Make sure the reverse
lockout solenoid operates.
Go to step 14.
Replace the reverse lockout solenoid.
14. Reinstall the reverse lockout solenoid, and
reconnect the solenoid 2P connector.
15. Turn the ignition switch ON (II).
16. Measure the voltage between ECM connector B7
terminal (2002-2004 models) or E2 terminal
(2005-2006 models) and body ground.
Check for loose connectors at ECM connector
B (24P) (2002-2004 models) or E (31P) (2005-2006
models). If necessary, update the ECM if it does not
have the latest software, or substitute a known-
good ECM (see page 11-7), then recheck. If the
symptom/indication goes away with a known-good
ECM, replace the original ECM (see page 11-284).
Repair open in the wire between the reverse
lockout solenoid and the ECM (B7) (2002-2004
models) or ECM (E2) (2005-2006 models).
Terminal side of male terminals
Wire side of female terminals
Wire side of female terminals
Does the r ever se lockout solenoid oper ate
pr oper ly?
Is ther e batter y voltage?
05/06/27 18:11:05 61S6M040_130_0079
*01
S6M6AA9E34151150941FEAT00
*01
S6M6AA9E34151150941MFAT00
13-80
13-80
Reverse Lockout System
Reverse Lockout Solenoid Test
Reverse Lockout Solenoid
Disassembly/Reassembly
REVERSE LOCKOUT SOLENOID
2P CONNECTOR
A
B
1. Remove the reverse lockout solenoid (see page
13-80).
2. Connect battery positive terminal to the No. 2
terminal of the reverse lockout solenoid 2P
connector, and connect the battery negative
terminal to the No. 1 terminal.
3. Make sure the reverse lockout solenoid operates. If
the reverse lockout solenoid does not work, replace
it.
1. Make sure you have the anti-theft codes for the
radio, then write down the customer’s radio station
presets. Disconnect the negative cable from the
battery first, then disconnect the positive cable.
Remove the battery.
2. Remove the intake manifold cover (see step 6 on
page 5-2).
3. Remove the air cleaner housing (see step 7 on page
5-2).
4. Remove the intake air duct (see step 8 on page 5-2).
5. Remove the battery base (see step 5 on page 13-5).
6. Disconnect the trasmission ground cable (see step
6 on page 13-5).
7. Disconnect the back-up light switch connector, the
vehicle speed sensor (VSS) connector, the reverse
lockout solenoid connector, and the output shaft
speed sensor connector (see step 7 on page 13-5).
8. Carefully remove the shift cable, select cable, and
cable bracket together to avoid bending the cables
(see step 8 on page 13-6).
9. Remove the bolts (A) and reverse lockout solenoid
(B).
Terminal side of male terminals
05/06/27 18:11:05 61S6M040_130_0080
*02
*03
13-81
B
C
A
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
10. Remove the roller (A), the select lock return spring
(C), and the select lock cam B.
11. Install in the reverse order of removal.
12. Remove any dirt and oil from the sealing surface.
Apply liquid gasket (P/N 08718-0001 or 08718-0002)
to the sealing surface.
NOTE: Do not install reverse locknut solenoid if too
much time has passed after applying the liquid
gasket (for P/N 08718-0002, no more than
4 minutes, for all others, no more than 5 minutes).
Instead, remove the old residue and reapply the
riquid gasket.
13. Install the reverse lockout solenoid.
14. Install the cable bracket, select cable, and shift
cable (see step 26 on page 13-17).
15. Connect the back-up light switch connector, the
vehicle speed sensor (VSS) connector, the reverse
lockout solenoid connector, and the output shaft
(countershaft) speed sensor connector (see step 28
on page 13-17).
16. Connect the transmission ground cable (see step 29
on page 13-18).
17. Install the battery base (see step 30 on page 13-18).
18. Install the intake air duct (see step 42 on page 5-19).
19. Install the air cleaner housing (see step 43 on page
5-19).
20. Install the intake manifold cover (see step 45 on
page 5-19).
21. Install the battery. Clean the battery posts and
cable terminals with sandpaper, then assemble
them apply grease to prevent corrosion. Connect
the positive cable to the battery first, then connect
the negative cable.
22. Enter the audio anti-theft codes, then enter the
customer’s audio station presets, and set the clock.
23. 2002-2004 models: Do the ECM idle learn
procedure (see page 11-349).
24. Do the power window control unit reset procedure
(see page 22-148).
05/06/27 18:11:21 61S6M040_130_0081
*01
S6M6AAJE34150700000DAAT00
2002-2004 models:
13-82
M/T Differential
Component Location Index
BALL BEARING
FINAL DRIVEN GEAR
DIFFERENTIAL CARRIER
BALL BEARING
Replacement, page 13-85
Replacement, page 13-84
Backlash Inspection, page 13-84
Replacement, page 13-84
Replacement, page 13-85
05/06/27 18:11:23 61S6M040_130_0082
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст