Acura RSX Honda Integra. Manual — part 471
03
02
01
Backprobing Spring-loaded Lock Connectors
Seats with Side Airbags
23-16
SRS
Precautions and Procedures (cont’d)
A
B
A
A
Label
SIDE AIRBAG
When checking voltage or resistance on this type of
connector the first time, you must remove the retainer
to insert the tester probe from the wire side.
NOTE: It is not necessary to reinstall the removed
retainer; the terminals will stay locked in the connector
housing.
To remove the retainer (A), insert a flat-tip screwdriver
(B) between the connector body and the retainer, then
carefully pry out the retainer. Take care not to break the
connector.
Seats with side airbags have a ‘‘SIDE AIRBAG’’ label on
the seat-back. Because the component parts (seat-back
cover, cushion, etc.) of seats with and without airbags
are different, make sure you install only the correct
replacement parts.
• When cleaning, do not saturate the seat with liquid,
and do not spray steam on the seat.
• Do not repair a torn or frayed seat-back cover.
Replace the seat-back cover.
• After a collision in which the side airbag was
deployed, replace the side airbag with new parts. If
the seat-back cushion is split, it must be replaced. If
the seat-back frame is deformed, it must be replaced.
• Never put aftermarket accessories on the seat (covers,
pads, seat heaters, lights, etc.).
05/06/27 18:08:02 61S6M040_230_0016
*05
Disconnecting System Connectors
23-17
SRS FRONT SENSOR
WIRE HARNESS
J
G
ENGINE COMPARTMENT
WIRE HARNESS
FLOOR
WIRE HARNESS
F
H
FLOOR
WIRE HARNESS
L
E
D
B
K
DASHBOARD WIRE
HARNESS
FRONT
PASSENGER’S
AIRBAG
CABLE
REEL
DRIVER’S
AIRBAG
FRONT
PASSENGER’S
SEAT BELT
TENSIONER
FRONT
PASSENGER’S
SEAT BELT
BUCKLE
TENSIONER
DRIVER’S
SEAT BELT
BUCKLE
TENSIONER
DRIVER’S
SIDE AIRBAG
DRIVER’S
SIDE IMPACT
SENSOR
FRONT
PASSENGER’S
SIDE IMPACT
SENSOR
FRONT
PASSENGER’S
SIDE AIRBAG
RIGHT FRONT
IMPACT
SENSOR
LEFT FRONT
IMPACT
SENSOR
DRIVER’S
SEAT BELT
TENSIONER
I
SRS UNIT
CONNECTOR A
(18P)
SRS UNIT
CONNECTOR B
(18P)
SRS UNIT
Before removing a front airbag, side airbag, or other SRS related devices (the SRS unit, the cable reel, the front impact
sensor, the side impact sensors, the seat belt buckle tensioners, and the seat belt tensioner connector), disconnecting
connectors from related devices, or removing the dashboard or the steering column, disconnect the airbag connectors
or the side airbag connectors to prevent accidental deployment. Turn the ignition switch OFF and disconnect the
negative cable from the battery, and wait at least 3 minutes before beginning the following procedures.
• Before disconnecting SRS unit connector A (18P) from the SRS unit, disconnect the driver’s airbag 4P connector (B),
the front passenger’s airbag 4P connector (D), the left side seat belt tensioner 2P connector (E), and the right side
seat belt tensioner 2P connector (F).
• Before disconnecting SRS unit connector B from the SRS unit, disconnect both side airbag 2P connectors (G, H) and
both seat belt buckle tensioner 4P connectors (I, J).
• Before disconnecting the cable reel 4P connector (K), disconnect the driver’s airbag 4P connector (B).
• Before disconnecting the floor wire harness 4P connector (L), disconnect both seat belt tensioner 2P connectors
(E, F).
(cont’d)
05/06/27 18:08:02 61S6M040_230_0017
01
02
03
Driver’s Airbag
Front Passenger’s Airbag
Side Airbag
23-18
SRS
Precautions and Procedures (cont’d)
A
A
A
1. Disconnect the negative battery cable, and wait at
least 3 minutes.
2. Remove the access panel from the steering wheel,
then disconnect the driver’s airbag 4P connector
(A) from the cable reel.
3. Remove the glove box, then disconnect the front
passenger’s airbag 4P connector (A) from the
dashboard wire harness.
4. Disconnect both side airbag 2P connectors (A) from
the floor wire harness.
05/06/27 18:08:03 61S6M040_230_0018
04
07
*06
Seat Belt Tensioner
Seat Belt Buckle Tensioner
SRS Unit
23-19
A
A
A
B
C
5. Disconnect the floor wire harness 2P connector
from both seat belt tensioners.
6. Disconnect both seat belt buckle tensioner 4P
connectors (A).
7. Disconnect SRS unit connector A, and/or SRS unit
connector B, and/or SRS unit connector C from the
SRS unit.
05/06/27 18:08:03 61S6M040_230_0019
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст