Acura RSX Honda Integra. Manual — part 469
*01
*02
S6M6A00H46200053401MAAT00
Retractor
In-vehicle
Front
Rear
23-8
Seat Belts
Inspection
2.5 °
40 °
15 °
15 °
40 °
40 °
15 °
15 °
40 °
A
Inside
Forward
22.5 °
40 °
15 °
15 °
40 °
40 °
15 °
15 °
40 °
A
Inside
Forward
For front seat belt retractor with seat belt tensioner,
review the SRS component locations (see page 23-10)
and the precautions and procedures (see page 23-11)
before performing repairs or service.
1. Before installing the retractor, check that the seat
belt can be pulled out freely.
2. Make sure that the seat belt does not lock when the
retractor (A) is leaned slowly up to 15 ° from the
mounted position. The seat belt should lock when
the retractor is leaned over 40 °. Do not attempt to
disassemble the retractor.
3. Replace the seat belt with a new assembly if there
is any abnormality. Do not disassemble any part of
the seat belt for any reason.
1. Check that the seat belt is not twisted or caught on
anything.
2. After installing the anchors, check for free
movement on the anchor bolts. If necessary,
remove the anchor bolts and check that the
washers and other parts are not damaged or
improperly installed.
3. Check the seat belts for damage or discoloration.
Clean with a shop towel if necessary. Use only
soap and water to clean.
NOTE: Dirt buildup in the loops of the upper
anchors can cause the seat belts to retract slowly.
Wipe the inside of the loops with a clean cloth
dampened in isopropyl alcohol.
4. Check that the seat belt does not lock when pulled
out slowly. The seat belt is designed to lock only
during a sudden stop or impact.
5. Make sure that the seat belt will retract
automatically when released.
6. For each passenger’s seat belt, check the seat belt
retractor locking mechanism ALR (automatic
locking retractor). This function is for securing child
seats.
–1 Pull the seat belt all the way out to engage the
ALR. The seat belt should retract with a soft,
ratcheting sound, but not extend. This is
normal.
–2 To disengage the ALR, release the seat belt and
allow it to fully retract, then pull the seat belt
out part-way. The seat belt should retract and
extend normally.
7. Replace the seat belt with a new assembly if there
is any abnormality. Do not disassemble any part of
the seat belt for any reason.
05/06/27 18:07:55 61S6M040_230_0008
01
S6M6A00H14800016901KDAT00
23-9
Child Seat Tether Anchor Removal/Installation
A
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
B
B
A
C
D
1. Open the child seat tether anchor cap (A) in the
trunk side trim panel (B).
2. Remove the child seat tether anchor (C). Do not
remove the toothed washer (D) from the tether
anchor.
3. Install the anchor in the reverse order of removal,
and apply liquid thread lock to the threads of the
anchor bolt(s).
05/06/27 18:07:56 61S6M040_230_0009
*01
S6M6A00H46400000000DAAT00
23-10
SRS
Component Location Index
OPDS SENSOR/SEAT-BACK
OPDS UNIT
MEMORY ERASE
SIGNAL (MES)
CONNECTOR (2P)
DATA LINK
CONNECTOR
(DLC) 16P
FRONT PASSENGER’S AIRBAG
DRIVER’S SIDE AIRBAG
DRIVER’S AIRBAG
SRS UNIT
DRIVER’S SIDE IMPACT SENSOR
FRONT PASSENGER’S
SIDE AIRBAG
SIDE AIRBAG CUTOFF INDICATOR
SRS INDICATOR
FRONT PASSENGER’S SEAT
BELT TENSIONER
DRIVER’S SEAT BELT TENSIONER
FRONT PASSENGER’S SIDE
IMPACT SENSOR
CABLE REEL
FRONT PASSENGER’S SEAT BELT BUCKLE TENSIONER
DRIVER’S SEAT BELT BUCKLE TENSIONER
LEFT FRONT IMPACT SENSOR
RIGHT FRONT IMPACT SENSOR
Replacement, page 20-79
Initialization, page 23-24
Replacement, page 23-143
Replacement, page 23-132
Disposal, page 23-135
Replacement, page 23-134
Disposal, page 23-135
Replacement, page 23-130
Disposal, page 23-135
Replacement, page 23-141
Replacement, page 23-142
Replacement, page 23-134
Disposal, page 23-135
Troubleshooting, page 23-123
Replacement, page 23-4
Disposal, page 23-135
Replacement, page 23-4
Disposal, page 23-135
Replacement, page 23-142
Replacement, page 23-138
Replacement, page 23-5
Replacement, page 23-5
Replacement, page 23-144
Replacement, page 23-144
05/06/27 18:08:00 61S6M040_230_0010
*01
S6M6A00H46400000000AAAT00
General Precautions
Steering-related Precautions
Cable Reel Alignment
23-11
Precautions and Procedures
Please read the following precautions carefully before
performing the airbag system service. Observe the
instructions described in this manual, or the airbags
could accidentally deploy and cause damage or injuries.
• Except when performing electrical inspections,
always turn the ignition switch OFF, disconnect the
negative cable from the battery, and wait at least
3 minutes before beginning work.
NOTE: The SRS memory is not erased even if the
ignition switch is turned OFF or the battery cables are
disconnected from the battery.
• Use replacement parts which are manufactured to the
same standards and quality as the original parts. Do
not install used SRS parts. Use only new parts when
making SRS repairs.
• Carefully inspect any SRS part before you install it.
Do not install any part that shows signs of being
dropped or improperly handled, such as dents, cracks,
or deformation.
• Before removing any of the SRS parts (including
disconnection of the connectors), always disconnect
the SRS connector.
• Use only a digital multimeter to check the system. If it
is not a Honda multimeter, make sure its output is
10 mA (0.01 A) or less when switched to the lowest
value in the ohmmeter range. A tester with a higher
output could cause accidental deployment and
possible injury.
• Do not put objects on the front passenger’s airbag.
• The original radio has a coded theft protection circuit.
Be sure to get the customer’s radio code and write
down the frequencies for the radio’s preset stations
before disconnecting the battery negative cable.
• Before returning the vehicle to the customer, enter
the radio code, then enter the customer’s radio
station presets, and set the clock. Do the idle learn
procedure (see page 11-349).
• Misalignment of the cable reel could cause an open in
the wiring, making the SRS system and the horn
inoperative. Center the cable reel whenever the
following is performed (see step 6 on page 23-140).
– Installation of the steering wheel
– Installation of the cable reel
– Installation of the steering column
– Other steering-related adjustment or installation
• Do not disassemble the cable reel.
• Do not apply grease to the cable reel.
• If the cable reel shows any signs of damage, replace
it with a new one. For example, if it does not rotate
smoothly, replace the cable reel.
(cont’d)
05/06/27 18:08:00 61S6M040_230_0011
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст