Acura RSX Honda Integra. Manual — part 124
S6M6AALK72100090630FAAT00
−
−
−
−
−
−
−
−
DTC P0630:
YES
NO
YES
NO
YES
NO
YES
NO
11-202
PGM-FI System
DTC Troubleshooting (cont’d)
VIN Not Programmed or
Mismatch
(2005-2006 models)
NOTE: This DTC is stored only when the ECM/PCM does
not have the VIN information of the vehicle. Use the
HDS to fill the missing VIN information.
1. Turn the ignition switch ON (II).
2. Check the VIN with the HDS.
Go to step 5.
Go to step 3.
3. Input the VIN to the ECM/PCM with the HDS.
Go to step 5.
Go to step 4.
4. Check for DTCs with the HDS.
Go to the DTC P0603 troubleshooting.
Update the ECM/PCM if it does not have the
latest software, or substitute a known-good ECM/
PCM (see page 11-6), then recheck. If the symptom/
indication goes away with a known-good ECM/PCM,
replace the original ECM/PCM (see page 11-284).
5. Clear the DTC with the HDS.
6. Turn the ignition switch OFF.
7. Turn the ignition switch ON (II), and wait 5 seconds.
8. Check for Temporary DTCs or DTCs with the HDS.
If DTC P0630 is indicated, update the ECM/
PCM if it does not have the latest software, or
substitute a known-good ECM/PCM (see page 11-6),
then recheck. If any other Temporary DTCs or DTCs
are indicated, go to the indicated DTC’s
troubleshooting.
Intermittent failure, system is OK at this
time.
Does the HDS show the vehicle’s V IN?
Does the scr een show COMPLET E?
Is DT C P0603 indicated?
Ar e any T empor ar y DT Cs or DT Cs indicated?
05/06/27 17:35:50 61S6M040_110_0202
S6M6AALK72100090685FAAT00
S6M6A02K77100090700FAAT00
−
−
DTC P0685:
DTC P0700:
YES
NO
11-203
11-203
ECM/PCM Power Control Circuit/
Internal Circuit Malfunction
(2005-2006 models)
A/T Control System Malfunction
NOTE: If the problem doesn’t return after you clear the
DTC, or if this DTC is stored intermittently, check for
loose terminals at the IGP line connectors before
replacing the ECM/PCM.
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, then let it idle for 30 seconds.
4. Turn the ignition switch OFF.
5. Start the engine, then let it idle for 30 seconds.
6. Turn the ignition switch OFF.
7. Turn the ignition switch ON (II).
8. Check for Temporary DTCs or DTCs with the HDS.
Update the ECM/PCM if it does not have the
latest software, or substitute a known-good ECM/
PCM (see page 11-6), then recheck. If the symptom/
indication goes away with a known-good ECM/PCM,
replace the original ECM/PCM (see page 11-284).
Intermittent failure, system is OK at this
time.
NOTE: This DTC is stored when there is a problem in
the A/T control system. Check for A/T DTCs with the
HDS, and go to the indicated DTC’s troubleshooting.
Is DT C P0685 indicated?
05/06/27 17:35:50 61S6M040_110_0203
01
02
03
S6M6AALK72100090720FAAT00
−
−
−
−
−
−
−
−
DTC P0720:
YES
NO
YES
NO
YES
NO
YES
NO
11-204
PGM-FI System
DTC Troubleshooting (cont’d)
OUTPUT SHAFT (COUNTERSHAFT)
SPEED SENSOR 3P CONNECTOR
VCC1
(YEL/RED)
NC
(BLU)
OUTPUT SHAFT (COUNTERSHAFT)
SPEED SENSOR 3P CONNECTOR
VCC1
(YEL/RED)
SG1
(GRN/WHT)
OUTPUT SHAFT (COUNTERSHAFT)
SPEED SENSOR 3P CONNECTOR
Output Shaft (Countershaft)
Speed Sensor Circuit Malfunction
(2005-2006 models)
NOTE: This DTC only occurs on M/T vehicles.
1. Start the engine. Hold the engine speed at
3,000 rpm without load (in neutral) until the
radiator fan comes on, then let it idle.
2. Test-drive several miles.
3. Check the C SHAFT SPD in the DATA LIST with the
HDS.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the output shaft (countershaft) speed sensor and
the ECM.
Go to step 4.
4. Turn the ignition switch OFF.
5. Disconnect the output shaft (countershaft) speed
sensor 3P connector.
6. Turn the ignition switch ON (II).
7. Measure voltage between output shaft
(countershaft) speed sensor 3P connector terminal
No. 1 and body ground.
Go to step 8.
Repair open in the wire between the ECM
(A21) and the output shaft (countershaft) speed
sensor, then go to step 17.
8. Measure voltage between output shaft
(countershaft) speed sensor 3P connector terminal
No. 2 and body ground.
Go to step 9.
Go to step 10.
9. Measure voltage between output shaft
(countershaft) speed sensor 3P connector terminals
No. 1 and No. 3.
Go to step 15.
Repair open in the wire between the output
shaft (countershaft) speed sensor and G101, then
go to step 17.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is any vehicle speed indicated?
Is ther e about 5 V ?
Is ther e about 5 V ?
Is ther e about 5 V ?
05/06/27 17:35:50 61S6M040_110_0204
−
04
05
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
YES
NO
11-205
NC (BLU)
ECM CONNECTOR A (31P)
NC (BLU)
ECM CONNECTOR A (31P)
10. Measure voltage between ECM connector terminal
A18 and body ground.
Repair open in the wire between the ECM
(A18) and the output shaft (countershaft) speed
sensor, then go to step 17.
Go to step 11.
11. Turn the ignition switch OFF.
12. Jump the SCS line with the HDS.
13. Disconnect ECM connector A (31P).
14. Check for continuity between ECM connector
terminal A18 and body ground.
Repair short in the wire between the ECM
(A18) and the output shaft (countershaft) speed
sensor, then go to step 17.
Go to step 24.
15. Turn the ignition switch OFF.
16. Replace the output shaft (countershaft) speed
sensor (see page 11-283), then go to step 17.
17. Reconnect all connectors.
18. Turn the ignition switch ON (II).
19. Reset the ECM with the HDS.
20. Do the ECM idle learn procedure (see page 11-349).
21. Test-drive under these conditions:
• Engine coolant temperature above 158 °F (70 °C)
• Transmission in 5th gear
• Engine speed at 2,000
3,000 rpm
• Drive for several minutes, then decelerate (with
the throttle fully closed) for 8 seconds
22. Check for Temporary DTCs or DTCs with the HDS.
If DTC P0720 is indicated, check for poor
connections or loose terminals at the output shaft
(countershaft) speed sensor and the ECM, then go
to step 1. If any other Temporary DTCs or DTCs are
indicated, go to the indicated DTC’s
troubleshooting.
Go to step 23.
23. Monitor the OBD STATUS for DTC P0720 in the
DTCs MENU with the HDS.
Troubleshooting is complete.
If the screen indicates FAILED, go to step 1
and recheck. If the screen indicates NOT
COMPLETED, go to step 21 and recheck.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Is ther e about 5 V ?
Is ther e continuity?
Ar e any T empor ar y DT Cs or DT Cs indicated?
Does the scr een indicate PASSED?
05/06/27 17:35:51 61S6M040_110_0205
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст