Acura RSX Honda Integra. Manual — part 497
*07
07
*08
−
−
’02-04 models
’05-06 models
YES
NO
23-120
SRS
DTC Troubleshooting (cont’d)
A
B
(C503)
DASHBOARD WIRE HARNESS 20P CONNECTOR C503
PNK/BLU
DASHBOARD WIRE HARNESS 21P CONNECTOR C503
PNK/BLU
27. Turn the ignition switch OFF.
28. Disconnect the floor wire harness 21P
or 20P
connector C503 (A) from the dashboard wire
harness connector C503 (B).
1: ’02-04 models
2: ’05-06 models
29. Turn the ignition switch ON (II).
30. Check for voltage between the No. 2
or No. 11
terminal of the dashboard wire harness 21P
or
20P
connector C503 and body ground. There
should be battery voltage.
1: ’02-04 models
2: ’05-06 models
Poor connection at the dashboard wire
harness 21P
or 20P
and floor wire harness 21P
or 20P
connectors, an open in floor wire harness,
seat subharness (with BOSE sound system), or
OPDS unit harness. Check the connection; if the
connection is OK, replace the faulty harness.
Poor connection at gauge assembly
connector B (18P ) or (16P ) or an open in
dashboard wire harness. Check gauge assembly
connector B (18P ) or (16P ); if the connections
are OK, replace the dashboard wire harness.
1: ’02-04 models
2: ’05-06 models
1
2
1
2
1
2
1
2
1
2
1
2
1
2
Terminal side of male terminals
Terminal side of male terminals
Is ther e batter y voltage?
05/06/27 18:11:07 61S6M040_230_0120
09
*09
08
11
−
−
−
−
’02-04 models
’05-06 models
YES
NO
YES
NO
23-121
GAUGE ASSEMBLY CONNECTOR B (18P)
YEL
GAUGE ASSEMBLY CONNECTOR B (16P)
YEL
A
D
B
31. Check for voltage between the No. 7
or No. 6
terminal of gauge assembly connector B (18P ) or
(16P ) and body ground. There should be battery
voltage.
1: ’02-04 models
2: ’05-06 models
Faulty side airbag cutoff indicator circuit;
replace the gauge assembly.
Open in dashboard wire harness; replace the
dashboard wire harness.
32. Turn the ignition switch OFF.
33. Disconnect the OPDS unit 8P connector D from the
OPDS unit (A) (see page 23-143).
34. Turn the ignition switch ON (II).
Go to step 35.
Faulty OPDS unit; replace the OPDS unit.
35. Turn the ignition switch OFF.
36. Remove the gauge assembly (see page 22-74), then
disconnect gauge assembly connector B (18P ) or
(16P ) from the gauge assembly.
1: ’02-04 models
2: ’05-06 models
(cont’d)
1
2
1
2
1
2
Wire side of female terminals
Wire side of female terminals
Is ther e batter y voltage?
Does the side air bag cutof f indicator come on?
05/06/27 18:11:44 61S6M040_230_0121
12
*10
S6M6A00K79100081153FAAT00
−
−
−
−
−
−
−
−
’02-04 models
’05-06 models
YES
NO
YES
NO
YES
NO
YES
NO
DTC 15-3:
23-122
23-122
SRS
DTC Troubleshooting (cont’d)
GAUGE ASSEMBLY CONNECTOR B (18P)
PNK/BLU
GAUGE ASSEMBLY CONNECTOR B (16P)
PNK/BLU
37. Check resistance between the No. 8
or No. 7
terminal of gauge assembly connector B (18P ) or
(16P ) and body ground. There should be an open
circuit or at least 1 M
.
1: ’02-04 models
2: ’05-06 models
Short to ground in the side airbag cutoff
indicator circuit; replace the gauge assembly.
Short to ground in dashboard wire harness A,
the floor wire harness, seat subharness (with BOSE
sound system), or the OPDS unit harness; replace
the faulty harness.
NOTE: Aftermarket devices (fluorescent lights, laptop
computers, etc.) used near the front passenger’s seat-
back can interfere with the seat-back sensors and cause
a false DTC 15-3. If one of these devices was used,
erase the DTC, operate the device near the seat-back,
and recheck for DTCs. If DTC 15-3 is reset, erase it, and
do not use the device near the seat-back.
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Check the connection at the OPDS sensor harness
connector and the OPDS unit connector.
Go to step 4.
Reconnect the OPDS sensor harness
connector, and clear the DTC.
4. Replace the OPDS sensor/seat-back foam (see page
20-79), and reinitialize the OPDS system (see page
23-24).
5. Erase the DTC memory, then check for DTC 15-3.
Replace the OPDS unit (see page 23-143).
The system is OK.
1
2
1
2
Faulty OPDS Sensor
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Does the SRS indicator stay on?
Ar e the connections OK ?
Is DT C 15-3 indicated?
05/06/27 18:11:45 61S6M040_230_0122
−
01
02
*01
S6M6A00H46400056602FAAT00
−
−
−
−
SRS indicator does not come on
YES
NO
’02-04 models
’05-06 models
YES
NO
23-123
Symptom Troubleshooting
B
A
GAUGE ASSEMBLY CONNECTOR B (18P)
BLK
GAUGE ASSEMBLY CONNECTOR B (16P)
BLK
1. Turn the ignition switch ON (II), and see if the other
indicators come on (brake system, etc.).
Go to step 2.
Go to step 8.
2. Turn the ignition switch OFF, then remove the
gauge assembly (see page 22-74). Disconnect
gauge assembly connector A (22P ) or (20P ), and
B (18P ) or (16P ) from the gauge assembly.
1: ’02-04 models
2: ’05-06 models
3. Check resistance between the No. 18
or No. 16
terminal of gauge assembly connector B (18P ) or
(16P ) and body ground. There should be
0
1.0
.
1: ’02-04 models
2: ’05-06 models
Go to step 4.
Open in BLK wire of the dashboard wire
harness or faulty body ground terminal (G401)
(see page 22-59). If the body ground terminal is OK,
replace the dashboard wire harness.
(cont’d)
1
2
1
2
1
2
1
2
Wire side of female terminals
Wire side of female terminals
Do the other indicator s come on?
Is the r esistance as specif ied?
05/06/27 18:11:45 61S6M040_230_0123
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст