Acura RSX Honda Integra. Manual — part 468
01
02
01
S6M6A00H46200053401KBAT00
Front Seat Belt
23-4
Seat Belts
Front Seat Belt Replacement
B
7/16-20 UNF
32 N·m (3.3 kgf·m,
24 lbf·ft)
A
B
7/16-20 UNF
32 N·m (3.3 kgf·m,
24 lbf·ft)
A
B
6 x 1.0 mm
3.4 N·m (0.35 kgf·m,
2.5 lbf·ft)
D
C
7/16-20 UNF
32 N·m (3.3 kgf·m, 24 lbf·ft)
E
A
F
SRS components are located in this area. Review the
SRS component locations (see page 23-10) and the
precautions and procedures (see page 23-11) before
performing repairs or service.
NOTE: Check the front seat belts for damage, and
replace them if necessary.
1. Make sure you have the anti-theft code for the radio,
and then write down the frequencies for the preset
buttons.
2. Disconnect the negative cable from the battery, and
wait at least 3 minutes before beginning work.
3. Slide the front seat forward fully.
4. Remove the rear side trim panel (see page 20-51).
5. Remove the lower anchor cap (A), and remove the
lower anchor bolt (B).
6. Remove the upper anchor cap (A), and remove the
upper anchor bolt (B).
7. Disconnect the seat belt tensioner connector (A).
Remove the retractor mounting self-tapping ET
screw (B) and the retractor bolt (C), then remove
the front seat belt (D) and retractor (E).
8. If necessary, remove the front seat belt
protector (F).
05/06/27 18:07:54 61S6M040_230_0004
04
05
06
07
Upper anchor bolt installation
Lower anchor bolt installation
Driver’s seat
Passenger’s seat with BOSE sound system
Seat Belt Buckle
23-5
COLLARS
UPPER ANCHOR
UPPER ANCHOR BOLT
BUSHING
TOOTHED LOCK WASHER
WASHER
SPRING WASHER
COLLAR
WASHER
COLLAR
LOWER ANCHOR BOLT
BUSHING
LOWER ANCHOR
SPRING WASHER
TOOTHED LOCK WASHER
WAVE WASHER
D
B
A
E
D
B
A
E
C
9. Install the belt in the reverse order of removal, and
note these items:
• If the threads on the retractor mounting
self-tapping ET screw are worn out, use an
oversized self-tapping ET screw (P/N 90133-
SZ4-003) made specifically for this application.
• Apply liquid thread lock to the anchor bolts
before reinstallation.
• Check that the retractor locking mechanism
functions (see page 23-8).
• Assemble the washers, collars, and bushings on
the upper and lower anchor bolts as shown.
• If the seat belt tensioner has been activated,
replace the front seat belt protector with a new
one.
• Before installing the anchor bolts, make sure
there are no twists or kinks in the seat belt.
• Make sure the seat belt tensioner connector is
plugged in properly.
• Reconnect the negative cable to the battery.
• Enter the anti-theft code for the radio, and then
enter the customer’s radio station presets.
• Reset the clock.
• ’02-04 models; Do the ECM/PCM idle learn
procedure (see page 11-349).
• Do the power window control unit reset
procedure (see page 22-148).
1. Make sure you have the anti-theft code for the radio,
and then write down the frequencies for the preset
buttons.
2. Disconnect the negative cable from the battery, and
wait at least 3 minutes before beginning work.
3. Remove the front seat (see page 20-75).
4. On the passenger’s seat with BOSE sound system,
remove the front stereo amplifier (see page 22-122).
5. Detach the seat belt switch connector clip (A) and
seat belt buckle tensioner connector clip (B), and on
the passenger’s seat with BOSE sound system,
disconnect the subharness connector (C) from the
seat belt switch connector. Remove the harness
band (D) from the seat cushion frame spring (E).
The driver’s seat and passenger’s seat with BOSE
sound system are shown, the passenger’s seat
without BOSE sound system is similar to the driver’s
seat.
(cont’d)
05/06/27 18:07:54 61S6M040_230_0005
01
01
02
S6M6A00H46200053402KBAT00
Rear Seat Belt
23-6
23-6
Seat Belts
Front Seat Belt Replacement
(cont’d)
Rear Seat Belt Replacement
A
7/16-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)
B
C
D
A
7/16-20 UNF
32 N·m (3.3 kgf·m,
24 lbf·ft)
B
7/16-20 UNF
32 N·m (3.3 kgf·m, 24 lbf·ft)
A
6. Remove the center anchor bolt (A), and remove the
seat belt buckle (B).
NOTE: The passenger’s seat is shown; the driver’s
seat is similar.
7. Pull the seat belt switch/tensioner harness (C) out
through the hole in the seat track, and remove the
seat belt buckle from the retainer band (D)
(passenger’s seat).
8. Install the buckle in the reverse order of removal,
and note these items:
• Apply liquid thread lock to the center anchor bolt
before reinstallation.
• Apply liquid thread lock to the seat mounting
bolts before reinstallation.
• Reconnect the negative cable to the battery.
• Enter the anti-theft code for the radio, and then
enter the customer’s radio station presets.
• Reset the clock.
• ’02-04 models; Do the ECM/PCM idle learn
procedure (see page 11-349).
• Do the power window control unit reset
procedure (see page 22-148).
NOTE: Check the rear seat belts for damage, and
replace them if necessary.
1. Remove the rear side trim panel (see page 20-51).
2. Remove the lower anchor bolt (A).
3. Remove the upper anchor cap (A), and remove the
upper anchor bolt (B).
05/06/27 18:07:55 61S6M040_230_0006
01
04
05
Upper anchor bolt installation
Seat Belt Buckles
23-7
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
D
B
7/16-20 UNF
32 N·m
(3.3 kgf·m,
24 lbf·ft)
C
COLLAR
UPPER ANCHOR
UPPER ANCHOR BOLT
BUSHING
TOOTHED LOCK WASHER
WASHER
SPRING WASHER
COLLARS
B
A
7/16-20 UNF
32 N·m (3.3 kgf·m, 24 lbf·ft)
4. Remove the quarter pillar trim as necessary
(see page 20-52).
5. Remove the retractor mounting bolt (A) and the
retractor bolt (B), then remove the rear seat belt (C)
and retractor (D).
6. Install the belt in the reverse order of removal, and
note these items:
• Apply liquid thread lock to the anchor bolts
before reinstallation.
• Check that the retractor locking mechanism
functions as described (see page 23-8).
• Assemble the washers, collars, and bushing on
the upper anchor bolt as shown.
• Before installing the anchor bolt, make sure there
are no twists or kinks in the seat belt.
1. Remove the rear seat cushion (see page 20-85).
2. Remove the center anchor bolts (A), and remove
the seat belt buckles (B).
3. Install the buckles in the reverse order of removal,
and apply liquid thread lock to the anchor bolts
before reinstallation.
05/06/27 18:07:55 61S6M040_230_0007
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст