Acura RSX Honda Integra. Manual — part 493
01
02
S6M6A00K79100081133FAAT00
−
−
−
−
DTC 13-3:
Special Tools Required
YES
NO
YES
NO
23-104
SRS
DTC Troubleshooting (cont’d)
A
A
B
A
B
07YAZ-S3AA100
07SAZ-TB4011A
No Signal from the Driver’s Side
Impact Sensor
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead H 07YAZ-S3AA100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Check the connection between the floor wire
harness 2P connector and the driver’s side impact
sensor.
Go to step 5.
Replace the driver’s side impact sensor
and/or the floor harness, as needed (see page
23-142).
5. Disconnect the driver’s side airbag and front
passenger’s side airbag 2P connectors (A), and
disconnect both seat belt buckle tensioner 4P
connectors (B).
6. Disconnect the floor wire harness 2P connector (A)
from the driver’s side impact sensor (B).
7. Connect the SRS inflator simulator (jumper
connector) and the simulator lead H to the floor
wire harness 2P connector.
Does the SRS indicator stay on?
Is the connection OK ?
05/06/27 18:11:02 61S6M040_230_0104
−
01
*01
01
S6M6A00K79100081134FAAT00
−
−
−
−
YES
NO
YES
NO
DTC 13-4:
23-105
23-105
B
SRS UNIT CONNECTOR B (18P)
A
A
B
8. Disconnect SRS unit connector B (18P) from the
SRS unit.
9. Check resistance between the No. 8 and No. 15
terminals of SRS unit connector B (18P). There
should be 0
1.0
.
Faulty driver’s side impact sensor or SRS
unit; replace the driver’s side impact sensor
(see page 23-142). If the problem is still present,
replace the SRS unit (see page 23-141).
Open in floor wire harness; replace the floor
wire harness.
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s side airbag and front
passenger’s side airbag 2P connectors (A), and
disconnect both seat belt buckle tensioner 4P
connectors (B).
(cont’d)
Faulty Power Supply to the Driver’s
Side Impact Sensor
Wire side of female terminals
Is the r esistance as specif ied?
Does the SRS indicator stay on?
05/06/27 18:11:02 61S6M040_230_0105
02
01
*01
*02
−
−
−
−
YES
NO
YES
NO
23-106
SRS
DTC Troubleshooting (cont’d)
B
A
B
SRS UNIT CONNECTOR B (18P)
SRS UNIT CONNECTOR B (18P)
5. Disconnect the floor wire harness 2P connector (A)
from the driver’s side impact sensor (B).
6. Disconnect SRS unit connector B (18P) from the
SRS unit.
7. Check resistance between the No. 8 terminal of
SRS unit connector B (18P) and body ground. There
should be an open circuit or at least 1 M
.
Go to step 8.
Short to ground in the floor wire harness;
replace the floor wire harness.
8. Check resistance between the No. 8 and No. 15
terminals of SRS unit connector B (18P). There
should be an open circuit or at least 1 M
.
Faulty driver’s side impact sensor or SRS
unit; replace the driver’s side impact sensor
(see page 23-142). If the problem is still present,
replace the SRS unit (see page 23-141).
Short in the floor wire harness; replace the
floor wire harness.
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
05/06/27 18:11:02 61S6M040_230_0106
01
02
S6M6A00K79100081143FAAT00
−
−
−
−
DTC 14-3:
Special Tools Required
YES
NO
YES
NO
23-107
A
A
B
B
A
07YAZ-S3AA100
07SAZ-TB4011A
No Signal from the Front
Passenger’s Side Impact Sensor
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead H 07YAZ-S3AA100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Check the connection between the floor wire
harness 2P connector and the front passenger’s
side impact sensor.
Go to step 5.
Poor connection between the floor wire
harness 2P connector and the front passenger’s
side impact sensor; replace the front passenger’s
side impact sensor and/or the floor harness, as
needed (see page 23-142).
5. Disconnect the driver’s side airbag and front
passenger’s side airbag 2P connectors (A), and
disconnect both seat belt buckle tensioner 4P
connectors (B).
6. Disconnect the floor wire harness 2P connector (A)
from the front passenger’s side impact sensor (B).
7. Connect the SRS inflator simulator (jumper
connector) and the simulator lead H to the floor
wire harness 2P connector.
(cont’d)
Does the SRS indicator stay on?
Is the connection OK ?
05/06/27 18:11:03 61S6M040_230_0107
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст