Acura RSX Honda Integra. Manual — part 484
01
02
S6M6A00K79100081221FAAT00
−
−
−
−
DTC 22-1:
Special Tools Required
YES
NO
YES
NO
23-68
SRS
DTC Troubleshooting (cont’d)
07SAZ-TB4011A
A
07XAZ-SZ30100
A
B
Open or Increased Resistance in
Front Passenger’s Seat Belt Buckle Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s seat belt buckle
tensioner 4P connector (A) from the floor wire
harness.
5. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the floor
wire harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Open or increased resistance in the front
passenger’s seat belt buckle tensioner; replace the
front passenger’s seat belt buckle (see page 23-5).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect both side airbag 2P connectors (A) and
the driver’s seat belt buckle tensioner 4P
connector (B).
Does the SRS indicator stay on?
Is DT C 22-1 indicated?
05/06/27 18:09:52 61S6M040_230_0068
−
01
*01
01
S6M6A00K79100081223FAAT00
−
−
−
−
YES
NO
Special Tools Required
YES
NO
DTC 22-3:
23-69
23-69
B
SRS UNIT CONNECTOR B (18P)
07SAZ-TB4011A
A
07XAZ-SZ30100
11. Disconnect SRS unit connector B (18P) from the
SRS unit. Do not disconnect the simulator lead
from the floor wire harness 4P connector.
12. Check resistance between the No. 2 and No. 11
terminals of SRS unit connector B (18P). There
should be 2.0
3.0
.
Faulty SRS unit or poor connection at SRS
unit connector B (18P) and at the SRS unit. Check
the connection; if the connection is OK, replace the
SRS unit (see page 23-141).
Open or increased resistance in the floor wire
harness; replace the floor wire harness.
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s seat belt buckle
tensioner 4P connector (A) from the floor wire
harness.
5. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the floor
wire harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
(cont’d)
Short to Another Wire or
Decreased Resistance in Front Passenger’s
Seat Belt Buckle Tensioner
Wire side of female terminals
Is the r esistance as specif ied?
Does the SRS indicator stay on?
05/06/27 18:09:52 61S6M040_230_0069
02
01
*01
−
−
−
−
YES
NO
YES
NO
23-70
SRS
DTC Troubleshooting (cont’d)
A
B
B
SRS UNIT CONNECTOR B (18P)
8. Read the DTC.
Go to step 9.
Short in the front passenger’s seat belt buckle
tensioner; replace the front passenger’s seat belt
buckle (see page 23-5).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect both side airbag 2P connectors (A) and
the driver’s seat belt buckle tensioner 4P
connector (B).
11. Disconnect SRS unit connector B (18P) from the
SRS unit.
12. Disconnect the simulator lead from the floor wire
harness 4P connector.
13. Check resistance between the No. 2 and No. 11
terminals of SRS unit connector B (18P). There
should be an open circuit or at least 1 M
.
Faulty SRS unit; replace the SRS unit
(see page 23-141).
Short in the floor wire harness; replace the
floor wire harness.
Wire side of female terminals
Is DT C 22-3 indicated?
Is the r esistance as specif ied?
05/06/27 18:09:53 61S6M040_230_0070
01
02
S6M6A00K79100081224FAAT00
−
−
−
−
DTC 22-4:
Special Tools Required
YES
NO
YES
NO
23-71
07SAZ-TB4011A
A
07XAZ-SZ30100
A
B
Short to Power in Front Passenger’s
Seat Belt Buckle Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s seat belt buckle
tensioner 4P connector (A) from the floor wire
harness.
5. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the floor
wire harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Short to power in the front passenger’s seat
belt buckle tensioner; replace the front passenger’s
seat belt buckle (see page 23-5).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect both side airbag 2P connectors (A) and
the driver’s seat belt buckle tensioner 4P
connector (B).
(cont’d)
Does the SRS indicator stay on?
Is DT C 22-4 indicated?
05/06/27 18:09:53 61S6M040_230_0071
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст