Acura RSX Honda Integra. Manual — part 482
01
01
S6M6A00K79100081041FAAT00
−
−
−
−
−
−
DTC 4-1:
Special Tools Required
YES
NO
YES
NO
YES
NO
23-60
SRS
DTC Troubleshooting (cont’d)
07SAZ-TB4011A
07TAZ-SZ5011A
A
A
07SAZ-TB4011A
07XAZ-SZ30100
C504
Open or Increased Resistance in
Front Passenger’s Seat Belt Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead C 07TAZ-SZ5011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s seat belt
tensioner 2P connector from the floor wire harness
(A).
5. Connect the SRS inflator simulator (2
connector) and the simulator lead C to the floor
wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Open or increased resistance in the front
passenger’s seat belt tensioner; replace the front
passenger’s seat belt (see page 23-4).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the floor wire harness 4P connector (A)
from the dashboard wire harness C504.
11. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the
dashboard wire harness 4P connector C504.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Open or increased resistance in the floor wire
harness; replace the floor wire harness.
Does the SRS indicator stay on?
Is DT C 4-1 indicated?
Is DT C 4-1 indicated?
05/06/27 18:09:22 61S6M040_230_0060
−
03
02
*01
−
−
YES
NO
23-61
C
B
A
A
SRS UNIT CONNECTOR A (18P)
15. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
16. Disconnect the driver’s airbag connector (A), front
passenger’s airbag connector (B), and driver’s seat
belt tensioner connector (C).
17. Disconnect SRS unit connector A (18P) from the
SRS unit. Do not disconnect the simulator lead
from the dashboard wire harness.
18. Check resistance between the No. 9 terminal and
the No. 18 terminal of SRS unit connector A (18P).
There should be 2.0
3.0
.
Faulty SRS unit or poor connection at SRS
unit connector A (18P) and the SRS unit. Check the
connection; if the connection is OK, replace the
SRS unit (see page 23-141).
Open or increased resistance in the
dashboard wire harness; replace the dashboard
wire harness.
Wire side of female terminals
Is the r esistance as specif ied?
05/06/27 18:09:49 61S6M040_230_0061
01
01
S6M6A00K79100081043FAAT00
−
−
−
−
−
−
DTC 4-3:
Special Tools Required
YES
NO
YES
NO
YES
NO
23-62
SRS
DTC Troubleshooting (cont’d)
07SAZ-TB4011A
07TAZ-SZ5011A
A
A
07SAZ-TB4011A
07XAZ-SZ30100
C504
Short to Another Wire or Decreased
Resistance in Front Passenger’s Seat Belt
Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead C 07TAZ-SZ5011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s seat belt
tensioner 2P connector from the floor wire
harness (A).
5. Connect the SRS inflator simulator (2
connector) and the simulator lead C to the floor
wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Short in the front passenger’s seat belt
tensioner; replace the front passenger’s seat belt
(see page 23-4).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the floor wire harness 4P connector (A)
from the dashboard wire harness C504.
11. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the
dashboard wire harness 4P connector C504.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Short in the floor wire harness; replace the
floor wire harness.
Does the SRS indicator stay on?
Is DT C 4-3 indicated?
Is DT C 4-3 indicated?
05/06/27 18:09:50 61S6M040_230_0062
03
02
*01
−
−
YES
NO
23-63
C
B
A
A
SRS UNIT CONNECTOR A (18P)
15. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
16. Disconnect the driver’s airbag connector (A), front
passenger’s airbag connector (B), and driver’s seat
belt tensioner connector (C).
17. Disconnect SRS unit connector A (18P) from the
SRS unit.
18. Disconnect the simulator lead from the dashboard
wire harness 4P connector.
19. Check resistance between the No. 9 terminal and
the No. 18 terminal of SRS unit connector A (18P).
There should be an open circuit or at least 1 M
.
Faulty SRS unit; replace the SRS unit
(see page 23-141).
Short in the dashboard wire harness; replace
the dashboard wire harness.
Wire side of female terminals
Is the r esistance as specif ied?
05/06/27 18:09:50 61S6M040_230_0063
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст