Acura RSX Honda Integra. Manual — part 38
10
04
11
12
5-16
Engine Assembly
Engine Installation (cont’d)
B
A
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
B
A
23. Install the lower radiator hose.
24. Tighten the automatic transmission fluid (ATF) filter
mounting bolt (A), and install the ATF cooler hoses
(B) (A/T).
25. Install the splash shield.
26. Lower the vehicle on the hoist.
27. Install the upper radiator hose (A) and heater hoses
(B).
13
02
15
16
5-17
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
6 x 1.0 mm
11 N·m
(1.1 kgf·m, 8.0 lbf·ft)
B
A
A
B
28. Install the P/S pump.
29. Install the bolt securing the power steering (P/S)
hose bracket.
30. Install the drive belt (see page 4-43).
31. Push the engine control module (ECM)/powertrain
control module (PCM) connectors through the
bulkhead, then install the grommet (A).
32. Install the harness clamps (B).
33. Connect the ECM/PCM connectors (A) and main
wire harness connector (B).
34. Install the throttle cable (see page 11-409), then
adjust the cable (see page 11-408).
35. Install the cruise control actuator cable, then adjust
the cable (see page 4-69).
(cont’d)
17
18
19
20
5-18
Engine Assembly
Engine Installation (cont’d)
A
B
A
B
C
D
E
D
C
E
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
8 x 1.25 mm
24 N·m
(2.4 kgf·m, 17 lbf·ft)
B
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
C
B
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
36. Install the brake booster vacuum hose (A) and the
evaporative emission (EVAP) canister hose (B).
37. Install the fuel feed line (see page 11-370).
38. Install the select cable (A) and shift cable (B) using
the plastic washers (C), washers (D), and new cotter
pins (E) (M/T).
39. Install the clutch slave cylinder (A) and clutch line
bracket mounting bolt (B) (M/T).
40. Install the battery cable (A) on the under-hood
fuse/relay box, then install the harness clamps (B).
41. Install the ground cable (C).
21
22
23
5-19
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
A
C
B
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
42. Install the air intake duct.
43. Install the air cleaner housing (A) and connect the
intake air temperature (IAT) sensor connector (B).
44. Install the breather hose (C).
45. Install the intake manifold cover.
46. Install the battery. Clean the battery posts and
cable terminals with sandpaper, then assemble
them and apply grease to prevent corrosion.
47. Move the shift lever to each gear, and verify that
the A/T gear position indicator follows the
transmission range switch (A/T).
48. Check that the transmission shifts into gear
smoothly (M/T).
49. Inspect for fuel leaks. Turn the ignition switch
ON (II) (do not operate the starter) so the fuel pump
runs for about 2 seconds and pressurizes the fuel
line. Repeat this operation two or three times, then
check for fuel leakage at any point in the fuel line.
50. Refill the engine with engine oil (see step 3 on page
8-8).
51. Refill the transmission with fluid:
• Manual transmission (see page 13-4).
• Automatic transmission (see page 14-272).
52. Refill the radiator with engine coolant, and bleed
air from the cooling system with the heater valve
open (see step 7 on page 10-7).
(cont’d)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст