Acura RSX Honda Integra. Manual — part 475
01
01
S6M6A00K79100081011FAAT20
−
−
−
−
DTC 1-1:
Special Tools Required
YES
NO
YES
NO
23-32
SRS
DTC Troubleshooting
A
07XAZ-SZ30100
07SAZ-TB4011A
A
Open or Increased Resistance in
Driver’s Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s airbag 4P connector from
the cable reel (A).
5. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the cable
reel 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Open or increased resistance in the driver’s
airbag inflator; replace the driver’s airbag (see page
23-130).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the front passenger’s airbag 4P
connector (A) from the dashboard wire harness.
Does the SRS indicator stay on?
Is DT C 1-1 indicated?
05/06/27 18:08:43 61S6M040_230_0032
−
02
01
*01
−
−
YES
NO
23-33
A
A
SRS UNIT CONNECTOR A (18P)
11. Disconnect both seat belt tensioner 2P connectors
(A) from the floor wire harness.
12. Disconnect SRS unit connector A (18P) from the
SRS unit. Do not disconnect the simulator lead
from the cable reel.
13. Check resistance between the No. 7 and the No. 16
terminals and between the No. 6 and the No. 15
terminals of SRS unit connector A (18P). There
should be 2.0
3.0
.
Faulty SRS unit or poor connection at SRS
unit connector A (18P) and the SRS unit; check the
connection between the connector and the SRS
unit. If the connection is OK, replace the SRS unit
(see page 23-141).
Open or increased resistance in the
dashboard wire harness or the cable reel; replace
the cable reel (see page 23-138). If the problem is
still present, replace the dashboard wire harness.
Wire side of female terminals
Is the r esistance as specif ied?
05/06/27 18:08:43 61S6M040_230_0033
01
01
S6M6A00K79100081013FAAT00
−
−
−
−
DTC 1-3:
Special Tools Required
YES
NO
YES
NO
23-34
SRS
DTC Troubleshooting (cont’d)
A
07XAZ-SZ30100
07SAZ-TB4011A
A
Short to Another Wire or Decreased
Resistance in Driver’s Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s airbag 4P connector from
the cable reel (A).
5. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the cable
reel 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Short in the driver’s airbag inflator; replace
the driver’s airbag (see page 23-130).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the front passenger’s airbag 4P
connector (A) from the dashboard wire harness.
Does the SRS indicator stay on?
Is DT C 1-3 indicated?
05/06/27 18:08:44 61S6M040_230_0034
02
01
*01
*02
−
−
−
−
YES
NO
YES
NO
23-35
A
A
SRS UNIT CONNECTOR A (18P)
SRS UNIT CONNECTOR A (18P)
11. Disconnect both seat belt tensioner 2P connectors
(A) from the floor wire harness.
12. Disconnect SRS unit connector A (18P) from the
SRS unit.
13. Disconnect the simulator lead from the cable reel
4P connector.
14. Check resistance between the No. 7 and the No. 16
terminals and between the No. 6 and the No. 15
terminals of SRS unit connector A (18P). There
should be an open circuit or at least 1 M
.
Faulty SRS unit; replace the SRS unit
(see page 23-141).
Go to step 15.
15. Disconnect the cable reel from the dashboard wire
harness. Check resistance between the No. 7 and
the No. 16 terminals and between the No. 6 and the
No. 15 terminals of SRS unit connector A (18P).
There should be an open circuit or at least 1 M
.
Replace the cable reel (see page 23-138).
Replace the dashboard wire harness.
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
05/06/27 18:08:44 61S6M040_230_0035
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст