Acura RSX Honda Integra. Manual — part 476
01
01
02
S6M6A00K79100081014FAAT00
−
−
−
−
DTC 1-4:
Special Tools Required
YES
NO
YES
NO
23-36
SRS
DTC Troubleshooting (cont’d)
07XAZ-SZ30100
A
07SAZ-TB4011A
A
A
Short to Power in Driver’s Airbag
Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s airbag 4P connector from
the cable reel (A).
5. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the cable
reel 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Short to power in the driver’s airbag inflator;
replace the driver’s airbag (see page 23-130).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the front passenger’s airbag 4P
connector (A) from the dashboard wire harness.
11. Disconnect both seat belt tensioner 2P connectors
(A) from the floor wire harness.
Does the SRS indicator stay on?
Is DT C 1-4 indicated?
05/06/27 18:08:45 61S6M040_230_0036
01
*01
*02
−
−
−
−
YES
NO
YES
NO
23-37
A
SRS UNIT CONNECTOR A (18P)
SRS UNIT CONNECTOR A (18P)
12. Disconnect SRS unit connector A (18P) from the
SRS unit.
13. Disconnect the simulator lead from the cable reel
4P connector.
14. Reconnect the battery negative cable.
15. Turn the ignition switch ON (II).
16. Check for voltage between the No. 7 terminal of
SRS unit connector A (18P) and body ground,
between the No. 16 terminal and body ground,
between the No. 6 terminal and body ground, and
between the No. 15 terminal and body ground.
There should be 0.5 V or less.
Faulty SRS unit; replace the SRS unit
(see page 23-141).
Go to step 17.
17. Turn the ignition switch OFF.
18. Disconnect the cable reel from the dashboard wire
harness.
19. Turn the ignition switch ON (II).
20. Check for voltage between the No. 7 terminal of
SRS unit connector A (18P) and body ground,
between the No. 16 terminal and body ground,
between the No. 6 terminal and body ground, and
between the No. 15 terminal and body ground.
There should be 0.5 V or less.
Replace the cable reel (see page 23-138).
Replace the dashboard wire harness.
Wire side of female terminals
Wire side of female terminals
Is the voltage as specif ied?
Is the voltage as specif ied?
05/06/27 18:08:45 61S6M040_230_0037
01
01
02
S6M6A00K79100081015FAAT00
−
−
−
−
DTC 1-5:
Special Tools Required
YES
NO
YES
NO
23-38
SRS
DTC Troubleshooting (cont’d)
A
07XAZ-SZ30100
07SAZ-TB4011A
A
A
Short to Ground in Driver’s Airbag
Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s airbag 4P connector from
the cable reel (A).
5. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the cable
reel 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Short to ground in the driver’s airbag inflator;
replace the driver’s airbag (see page 23-130).
9. Disconnect the battery negative cable, and wait for
3 minutes.
10. Disconnect the front passenger’s airbag 4P
connector (A) from the dashboard wire harness.
11. Disconnect both seat belt tensioner 2P connectors
(A) from the floor wire harness.
Does the SRS indicator stay on?
Is DT C 1-5 indicated?
05/06/27 18:08:45 61S6M040_230_0038
01
*01
*02
−
−
−
−
YES
NO
YES
NO
23-39
A
SRS UNIT CONNECTOR A (18P)
SRS UNIT CONNECTOR A (18P)
12. Disconnect SRS unit connector A (18P) from the
SRS unit.
13. Disconnect the simulator lead from the cable reel
4P connector.
14. Check resistance between the No. 7 terminal of
SRS unit connector A (18P) and body ground,
between the No. 16 terminal and body ground,
between the No. 6 terminal and body ground, and
between the No. 15 terminal and body ground.
There should be an open circuit or at least 1 M
.
Faulty SRS unit; replace the SRS unit
(see page 23-141).
Go to step 15.
15. Disconnect the cable reel from the dashboard wire
harness.
16. Check resistance between the No. 7 terminal of
SRS unit connector A (18P) and body ground,
between the No. 16 terminal and body ground,
between the No. 6 terminal and body ground, and
between the No. 15 terminal and body ground.
There should be an open circuit or at least 1 M
.
Replace the cable reel (see page 23-138).
Replace the dashboard wire harness.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
05/06/27 18:08:46 61S6M040_230_0039
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст