Acura RSX Honda Integra. Manual — part 312
04
05
10
04
14-374
Shafts and Clutches
Clutch Disassembly (cont’d)
A
B
C
D
E
A
B
C
D
E
07LAE-PX40100
07LAE-PX40100 or
07HAE-PL50101
07GAE-PG40200 or
07GAE-PG4020A
A
B
C
7. Remove the clutch end plate (A), clutch discs (B) (3),
clutch waved-plates (C) (3), and waved spring (D)
from the 4th clutch drum (E).
8. Remove the clutch end plate (A), clutch discs (B) (3),
clutch waved-plates (C) (3), and waved spring (D)
from the 5th clutch drum (E).
9. Install the special tools.
10. Set the special tool (A) on the spring retainer (B) of
the 1st, 2nd, and 3rd clutches so the special tool
works on the clutch return spring (C).
05/06/27 17:59:33 61S6M040_140_0375
03
05
06
11
14-375
A
B
11. Be sure the special tool (A) is adjusted to have full
contact with the spring retainer (B) on the 4th and
5th clutches.
12. If either end of the special tool is set over an area of
the spring retainer which is unsupported by the
return spring, the retainer may be damaged.
13. Compress the return spring until the snap ring can
be removed.
14. Remove the snap ring with snap ring pliers.
15. Remove the special tools.
(cont’d)
05/06/27 17:59:33 61S6M040_140_0376
07
08
09
10
14-376
Shafts and Clutches
Clutch Disassembly (cont’d)
A
B
C
A
B
16. Remove the snap ring (A), spring retainer (B), and
return spring (C).
17. Wrap a shop rag around the clutch drum (A), and
apply air pressure to the fluid passage to remove
the piston (B). Place a finger tip on the other
passage while applying air pressure.
18. Remove the piston, then remove the O-rings from
the 4th and 5th clutch pistons.
19. Remove the piston, then remove the O-ring from
the 1st, 2nd, and 3rd clutch drum, and remove the
O-ring from each clutch piston.
05/06/27 17:59:34 61S6M040_140_0377
01
02
S6M6A02E10411310041MAAT00
Standard Thickness
Clutch Discs:
1.94 mm (0.076 in.)
Clutch Plates
1st, 2nd, and 3rd:
2.00 mm (0.079 in.)
4th and 5th
2002-2004 models: 2.00 mm (0.079 in.)
2005-2006 models: 2.30 mm (0.091 in.)
14-377
Clutch Inspection
A
A
1. Inspect the 4th and 5th clutch pistons and clutch
piston check valves (A).
2. If the clutch piston check valve is loose or damaged,
replace the clutch piston.
3. Check the spring retainer for wear and damage.
4. Check the oil seal (A) on the spring retainer of the
1st, 2nd, and 3rd clutches for wear, damage, and
peeling.
5. If the oil seal is worn, damaged, or peeling, replace
the spring retainer.
6. Inspect the clutch discs, clutch-plates, and clutch
end plate for wear, damage, and discoloration.
7. If the clutch discs are worn or damaged, replace
them as a set. If the clutch discs are replaced,
inspect the clutch-end-plate-to-top-disc clearance.
8. If any plate is worn, damaged, or discolored,
replace the damaged plate with the new plate, and
inspect the other waved-plates for a phase
difference. If the clutch plate is replaced, inspect
the clutch-end-plate-to-top-disc clearance.
9. If the clutch end plate is worn, damaged, or
discolored, inspect the clutch-end-plate-to-top-disc
clearance, then replace the clutch end plate.
05/06/27 17:59:34 61S6M040_140_0378
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст