Acura RSX Honda Integra. Manual — part 500
01
02
S6M6A00H46400012803KBAT00
Removal
23-132
SRS
Front Passenger’s Airbag Replacement
A
B
A
1. Disconnect the battery negative cable, and wait at
least 3 minutes before beginning work.
2. Remove the glove box (see page 20-67).
3. Disconnect the front passenger’s airbag 4P
connector (A) from the dashboard wire harness.
4. Remove the three mounting nuts (A) from the
bracket. Cover the lid and dashboard with a cloth,
and pry carefully with a screwdriver to lift the front
passenger’s airbag (B) out of the dashboard.
NOTE: The airbag lid has pawls on its side which
attach it to the dashboard.
05/06/27 18:11:48 61S6M040_230_0132
03
02
Installation
23-133
B
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
A
1. Place the new front passenger’s airbag (A) into the
dashboard. Tighten the front passenger’s airbag
mounting nuts (B).
2. Connect the front passenger’s airbag 4P connector
(A) to the dashboard wire harness, then reinstall
the glove box.
3. Reconnect the battery negative cable.
4. After installing the airbag, confirm proper system
operation: Turn the ignition switch ON (II); the SRS
indicator should come on for about 6 seconds and
then go off.
05/06/27 18:11:48 61S6M040_230_0133
01
02
03
S6M6A00H46400055381KBAT00
Removal
Installation
23-134
SRS
Side Airbag Replacement
A
B
A
B
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
NOTE: Review the front seat removal/installation
procedure (see page 20-75) before performing repair or
service.
1. Disconnect the battery negative cable, and wait at
least 3 minutes before beginning work.
2. Disconnect the side airbag harness 2P
connector (A).
3. Remove the seat assembly (see page 20-75) and
seat-back cover (see page 20-79).
4. Remove the mounting nut (A) and the side
airbag (B).
NOTE:
• If the side airbag lid is secured by tape, remove the
tape.
• Do not open the lid of the side airbag cover.
• Use new mounting nuts tightened to the specified
torque.
• Make sure that the seat-back cover is installed
properly. Improper installation may prevent proper
deployment.
• Be sure to install the harness wires so that they are
not pinched or interfering with other parts.
1. Place the new side airbag on the seat-back frame
(A). Tighten the side airbag mounting nut (B).
2. Install the seat-back cover (see page 20-79).
3. Install the seat assembly (see page 20-75), then
connect the side airbag harness 2P connector.
4. Move the seat cushion and the seat-back through
their full ranges of movement, making sure the
harness wires are not pinched or interfering with
other parts.
5. Reconnect the battery negative cable.
6. After installing the side airbag, confirm proper
system operation: Turn the ignition switch ON (II);
the SRS indicator should come on for about
6 seconds and then go off.
05/06/27 18:11:48 61S6M040_230_0134
01
02
S6M6A00H46400012802LBAT00
Special Tools Required
Driver’s Airbag
Front Passenger’s Airbag
Deploying Airbags in the Vehicle
23-135
Airbag Disposal
B
A
A
Deployment tool 07HAZ-SG00500
Before scrapping any airbags, side airbags, seat belt
tensioners, or seat belt buckle tensioners (including
those in a whole vehicle to be scrapped), the airbags,
side airbags, seat belt tensioners, or seat belt buckle
tensioners must be deployed. If the vehicle is still within
the warranty period, the Acura District Parts and
Service Manager must give approval and/or special
instruction before deploying the airbags, side airbags,
seat belt tensioners, or seat belt buckle tensioners. Only
after the airbags, side airbags, seat belt tensioners, or
seat belt buckle tensioners have been deployed (as the
result of vehicle collision, for example), can they be
scrapped. If the airbags, side airbags, seat belt
tensioners, and seat belt buckle tensioners appear
intact (not deployed), treat them with extreme caution.
Follow this procedure.
If an SRS equipped vehicle is to be entirely scrapped, its
airbags, side airbags, seat belt tensioners, and seat belt
buckle tensioners should be deployed while still in the
vehicle. The airbags, side airbags, seat belt tensioners,
and seat belt buckle tensioners should not be
considered as salvageable parts and should never be
installed in another vehicle.
1. Turn the ignition switch OFF, then disconnect the
battery negative cable, and wait at least 3 minutes.
2. Confirm that each airbag, side airbag, or seat belt
tensioner is securely mounted.
3. Confirm that the deployment tool is functioning
properly by following the check procedure on the
tool label.
4. Remove the access panel (A) from the steering
wheel, then disconnect the driver’s airbag 4P
connector (B) from the cable reel.
5. Remove the glove box, then disconnect the front
passenger’s airbag 4P connector (A) and
dashboard wire harness.
(cont’d)
05/06/27 18:11:49 61S6M040_230_0135
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст