Acura RSX Honda Integra. Manual — part 499
04
*06
−
−
’02-04 models
’05-06 models
YES
NO
23-128
SRS
Symptom Troubleshooting (cont’d)
GAUGE ASSEMBLY CONNECTOR A (22P)
GAUGE ASSEMBLY
CONNECTOR B (18P)
JUMPER WIRE
GAUGE ASSEMBLY CONNECTOR A (20P)
GAUGE ASSEMBLY
CONNECTOR B (16P)
JUMPER WIRE
5. Reconnect the battery negative cable.
6. Reconnect gauge assembly connector A (22P ) or
(20P ) to the gauge assembly.
1: ’02-04 models
2: ’05-06 models
7. Turn the ignition switch ON (II).
8. Install a jumper wire between the No. 15
or
No. 13
terminal of the gauge assembly connector
A (22P ) or (20P ) and the No. 7
or No. 6
terminal of the gauge assembly connector B (18P )
or (16P ). The SRS indicator should go off.
1: ’02-04 models
2: ’05-06 models
Faulty SRS unit or poor connection at SRS
unit connector C (8P) and the SRS unit; check the
connection. If the connection is OK, replace the
SRS unit (see page 23-141).
Faulty SRS indicator circuit in the gauge
assembly or poor connection at gauge assembly
connector A or B; check the connections. If the
connectors are OK, replace the gauge assembly.
1
2
1
2
1
2
1
2
1
2
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Does the SRS indicator go of f ?
05/06/27 18:11:47 61S6M040_230_0128
S6M6A00H46400000000MDAT00
23-129
Component Replacement/Inspection After Deployment
NOTE: Before doing any SRS repairs, use the HDS SRS
menu method to check for DTCs; refer to the DTC
Troubleshooting Index for the less obvious deployed
parts (seat belt tensioners, front impact sensors, side
airbag sensors, etc.).
After a collision where the seat belt tensioners
deployed, replace these items:
• Seat belt tensioners
• Seat belt buckle tensioners
• SRS unit
• Front impact sensors
After a collision where the frontal airbag(s) deployed,
replace these items:
• SRS unit
• Deployed airbag(s)
• Seat belt tensioners
• Seat belt buckle tensioners
• Front impact sensors
After a collision where the side airbag(s) deployed,
replace these items:
• SRS unit
• Deployed side airbag(s)
• Side impact sensor(s) for side(s) deployed
During the repair process, inspect these areas:
• Inspect all the SRS wire harnesses. Replace, don’t
repair, any damaged harnesses.
• Inspect the cable reel for heat damage. If there is any
damage, replace the cable reel.
After the vehicle is completely repaired, turn the
ignition switch ON(II). If the SRS indicator comes on for
about 6 seconds and then goes off, the SRS airbag
system is OK. If the indicator does not function properly,
use the HDS SRS menu method to read the DTC(s). If
this doesn’t retrieve any codes, use the HDS SCS menu
method. If you still cannot retrieve a code, go to SRS
Indicator Circuit Troubleshooting.
05/06/27 18:11:47 61S6M040_230_0129
01
02
S6M6A00H46400012802KBAT00
Removal
23-130
SRS
Driver’s Airbag Replacement
A
B
A
B
1. Disconnect the battery negative cable, and wait at
least 3 minutes before beginning work.
2. Remove the access panel (A) from the steering
wheel, then disconnect the driver’s airbag 4P
connector (B) from the cable reel.
3. Remove the two Torx bolts (A) using a Torx T30 bit.
Then remove the driver’s airbag (B).
05/06/27 18:11:47 61S6M040_230_0130
*01
02
Installation
23-131
B
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
B
A
1. Place the new driver’s airbag (A) in the steering
wheel, and secure it with new Torx bolts (B).
2. Connect the cable reel to the driver’s airbag 4P
connector (A), then install the access panel (B) on
the steering wheel.
3. Connect the battery negative cable.
4. After installing the airbag, confirm proper system
operation:
• Turn the ignition switch ON (II); the SRS indicator
should come on for about 6 seconds and then go
off.
• Make sure the horn works.
05/06/27 18:11:47 61S6M040_230_0131
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст