Acura RSX Honda Integra. Manual — part 454
+
−
+
−
01
02
S6M6A00J54300065721FEAT10
Windshield
Rear Window
22-156
Wipers/Washers
Wiper Motor Test
A
B
A
B
1. Remove the wiper arms, hood seals, and cowl
covers (see page 22-158).
2. Disconnect the 5P connector (A) from the wiper
motor (B).
3. Test the motor by connecting battery power to the
No. 5 terminal and ground the No. 1 terminal of the
wiper motor 5P connector. The motor should run. If
the motor does not run or fails to run smoothly,
replace the motor.
4. Connect an analog voltmeter between the No. 3 (
)
and No. 4 (
) terminals, and run the motor at low
or high speed. The voltmeter should indicate 12 V
and 4 V or less alternately. If it does not, replace the
windshield wiper motor.
1. Open the hatch, and remove the hatch trim panel
(see page 20-54).
2. Disconnect the 4P connector (A) from the wiper
motor (B).
3. Test the motor by connecting battery power to the
No. 1 terminal and ground the No. 3 terminal of the
wiper motor. The motor should run. If the motor
does not run or fails to run smoothly, replace the
motor.
4. Connect an analog voltmeter between the No. 4 (
)
and No. 2 (
) terminals, and run the motor.
The voltmeter should indicate 12 V and 4 V or less
alternately. If it does not, replace the rear window
wiper motor.
05/06/27 18:05:26 61S6M040_220_0157
*01
S6M6A00J54300065021FEAT10
01
S6M6A04J54300065011FEAT20
Canada
22-157
22-157
Washer Motor Test
Washer Fluid Level Switch Test
A
Windshield:
Rear:
B
C
B
A
1. Remove the left inner fender (see page 20-111).
2. Disconnect the 2P connectors (A) from the washer
motors (B).
3. Test the motor by connecting battery power to the
No. 1 terminal and ground the No. 2 terminal of the
washer motor. The motor should run.
• If the motor does not run or fails to run smoothly,
replace it.
• If the motor runs smoothly, but little or no
washer fluid is pumped, check for a disconnected
or blocked washer hose, or a clogged pump
outlet in the motor.
1. Partially remove the left inner fender (see page
20-111).
2. Disconnect the 2P connector (A) from the washer
fluid level switch (B).
3. Remove the washer fluid level switch from the
washer reservoir.
NOTE: Fluid may flow out of the opening.
4. Check for continuity between the No. 1 and No. 2
terminals in each float position (C).
• There should be continuity when the float is
down.
• There should be no continuity when the float is
up.
5. If the continuity is not as specified, replace the
switch.
Terminal side of male terminals
05/06/27 18:05:26 61S6M040_220_0158
01
02
03
S6M6A00J54300065721KBAT20
Windshield Wiper Motor
22-158
Wipers/Washers
Wiper Motor Replacement
B
C
D
A
18 N·m (1.8 kgf·m,13 lbf·ft)
B
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
B
A
C
8 N·m
(0.8 kgf·m, 6 lbf·ft)
B
C
18 N·m
(1.8 kgf·m, 13 lbf·ft)
A
1. Open the hood. Remove the nuts (A) and the
windshield wiper arms (B).
2. Remove the hood seals (C) and cowl covers (D).
3. Disconnect the 5P connector (A) from the wiper
motor (B).
4. Remove the four bolts and wiper linkage assembly
(C).
5. Scribe a line (A) across the link and windshield
wiper linkage to show the original adjustment.
Separate the windshield wiper linkage (B) from the
wiper motor (C).
6. Install in the reverse order of removal, and note
these items:
• Apply multipurpose grease to the moving parts.
• Before reinstalling the wiper arms, turn the wiper
switch ON, then OFF to return the wiper shafts to
the park position.
• If necessary, replace any damaged clips.
• Check the wiper motor operation.
05/06/27 18:05:26 61S6M040_220_0159
04
05
01
02
S6M6A00J54300065001KBAT10
Rear Window Wiper Motor
22-159
22-159
Washer Reservoir Replacement
B
A
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
C
9 N·m
(0.8 kgf·m,
7 lbf·ft)
A
B
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
B
A
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
1. Open the hatch, and remove the hatch trim panel
(see page 20-54).
2. Remove the mounting nut (A), wiper arm (B), and
special nut (C).
3. Disconnect the 4P connector (A) from the wiper
motor (B).
4. Remove the three bolts and wiper motor.
5. Install in the reverse order of removal.
Check the wiper motor operation.
1. Remove the left inner fender (see page 20-111).
2. Disconnect the 2P connector(s) (A) and washer tube
(B).
3. Remove the four bolts and washer reservoir (A).
4. Install the reservoir in the reverse order of removal.
Check the washer motor operation.
05/06/27 18:05:27 61S6M040_220_0160
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст