Acura RSX Honda Integra. Manual — part 455
01
S6M6A00J54300065041KBAT10
22-160
Wipers/Washers
Washer Tube Replacement
1. Remove the left inner fender (see page 20-111).
2. Remove the headliner (see page 20-55).
3. Remove the washer nozzles and clips, then remove the tubes.
4. Install in the reverse order of removal. Take care not to pinch the washer tubes. Check the washer operation.
05/06/27 18:05:27 61S6M040_220_0161
*01
S6M6A03J54211500000EAAT11
*01
S6M6A04J54211500000EAAT12
USA
Canada
22-161
22-161
Accessory Power Sockets
Circuit Diagram
BATTERY
UNDER-HOOD FUSE/RELAY BOX
No. 19 (100 A) No. 20 (40 A)
No. 14
(30 A)
WHT
BAT
ACC
IGNITION
SWITCH
ACC HOT in ACC (I)
and ON (II)
WHT/RED
WHT/RED
No. 3
(10 A)
No. 18
(15 A)
UNDER-DASH
FUSE/RELAY
BOX
RED/BLU
YEL/GRN
YEL/GRN
REAR
ACCESSORY
POWER
SOCKET
RELAY
WHT
YEL/GRN
BLK
BLK
BLK
YEL/GRN
2
1
2
1
G501
G401
G401
No. 20
(50 A)
WHT
BAT
ACC
IGNITION
SWITCH
ACC HOT in ACC (I)
and ON (II)
No. 18
(15 A)
UNDER-DASH
FUSE/RELAY
BOX
WHT/RED
BLK
YEL/GRN
2
1
G401
BATTERY
No. 19
(100 A)
UNDER-HOOD
FUSE/RELAY
BOX
REAR
ACCESSORY
POWER
SOCKET
FRONT
ACCESSORY
POWER
SOCKET
FRONT
ACCESSORY
POWER
SOCKET
05/06/27 18:05:28 61S6M040_220_0162
01
01
S6M6A00J54211512402FHAT30
Front
Rear
22-162
Accessory Power Sockets
Accessory Power Socket Test/Replacement
B
BLK
YEL/GRN
A
BLK
YEL/GRN
B
A
1. Remove the dashboard center lower cover
(see page 20-65).
2. Disconnect the 2P connector (A) from the socket (B).
3. Carefully pry the accessory power socket out from
the dashboard.
4. Inspect the connector terminals to be sure they are
all making good contact.
• If the terminals are bent, loose or corroded,
repair them as necessary, and recheck the
system.
• If the terminals look OK, go to step 5.
5. Turn the ignition switch ACC (I), and check for
voltage between the No. 1 and No. 2 terminals.
• There should be battery voltage.
• If there is no battery voltage, check for:
– Poor ground (G 401).
– An open in the wire.
– Blown No. 18 (15 A) fuse in the under-dash
fuse/relay box.
1. Remove the rear console cover (see page 20-62).
2. Disconnect the 2P connector (A) from the socket (B).
3. Carefully pry the accessory power socket out from
the rear console cover.
4. Inspect the connector terminals to be sure they are
all making good contact.
• If the terminals are bent, loose or corroded,
repair them as necessary, and recheck the
system.
• If the terminals look OK, go to step 5.
5. Turn the ignition switch ACC (I), and check for
voltage between the No. 1 and No. 2 terminals.
• There should be battery voltage.
• If there is no battery voltage, check for:
– Poor ground (G 401, G501).
– An open in the wire.
– Blown No. 18 (15 A) fuse in the under-dash
fuse/relay box.
– Blown No. 3 (10 A) fuse in the under-dash fuse/
relay box.
– Faulty rear accessory power socket relay.
Wire side of
female terminals
Wire side of
female terminals
05/06/27 18:05:28 61S6M040_220_0163
*04
S6M6A00J46643400000DAAT30
22-163
Keyless/Power Door Lock System
Component Location Index
UNLOCK BUTTON
LOCK BUTTON
PANIC BUTTON
TRANSMITTER
KEYLESS RECEIVER UNIT
MUTIPLEX CONTROL UNIT
IGNITION KEY SWITCH
PASSENGER’S DOOR LOCK SWITCH
PASSENGER’S DOOR LOCK ACTUATOR
NOISE CONDENSER
PASSENGER’S DOOR SWITCH
HATCH LOCK ACTUATOR
DRIVER’S DOOR SWITCH
DRIVER’S DOOR LOCK
ACTUATOR/KNOB SWITCH
DRIVER’S DOOR
LOCK SWITCH
HATCH LATCH SWITCH
Test, page 22-173
Programming, page 22-174
Input Test, page 22-169
Input Test, page 22-166
Test, page 22-104
Test, page 22-170
Test, page 22-172
Capacity Test, page 22-128
Test, page 22-171
Actuator Test, page 22-172
Knob Switch Test, page 22-170
Test, page 22-170
Test, page 22-108
Replacement, page 20-122
05/06/27 18:05:31 61S6M040_220_0164
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст