Acura RSX Honda Integra. Manual — part 271
−
01
02
S6M6APPK77100090962FAAT00
−
−
−
−
−
−
−
−
DTC P0962:
2005-2006 Models
YES
NO
YES
NO
YES
NO
YES
NO
14-209
A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE A CONNECTOR
(BLK)
A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE A CONNECTOR
Problem in A/T Clutch Pressure
Control Solenoid Valve A Circuit
NOTE:
• Record all freeze data and review General
Troubleshooting Information (see page 14-8) before
you troubleshoot.
• This code is caused by an electrical circuit problem
and cannot be caused by a mechanical problem in the
transmission.
1. Clear the DTC with the HDS.
2. Check that DTC P0962 recurs.
Go to step 6.
Go to step 3.
3. Choose Clutch Pressure Control Solenoid Control
in Miscellaneous Test Menu, and test the A/T clutch
pressure control solenoid valve A with the HDS.
4. Drive with the A/T clutch pressure control solenoid
valve A at 1.0 A in Clutch Pressure Control Solenoid
Control menu.
5. Monitor the OBD status for P0962 in the DTCs/
Freeze Data in A/T Mode Menu for a pass/fail.
Go to step 6.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the A/T clutch pressure control solenoid valve A
and PCM. If the tester indicates NOT COMPLETED,
return to step 3 and recheck.
6. Turn the ignition switch OFF.
7. Disconnect the A/T clutch pressure control solenoid
valve A connector.
8. Measure A/T clutch pressure control solenoid valve
A resistance at the solenoid connector.
Go to step 9.
Replace the A/T clutch pressure control
solenoid valve A (see page 14-263), then go to step
12.
9. Check for continuity between A/T clutch pressure
control solenoid valve A connector terminal No. 2
and body ground.
Go to step 10.
Repair open in the wire between the A/T
clutch pressure control solenoid valve A and
ground (G101), or repair poor ground (G101), then
go to step 12.
(cont’d)
Terminal side of male terminals
Wire side of female terminals
Is DT C P0962 indicated?
Does the r esult indicate a f ailed?
Is ther e 3
10
?
Is ther e continuity?
05/06/27 17:52:14 61S6M040_140_0210
03
−
−
−
−
YES
NO
YES
NO
14-210
Automatic Transmission
DTC Troubleshooting (cont’d)
(BLK)
LS A (RED/BLK)
A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE A CONNECTOR
10. Turn the ignition switch ON (II).
11. Measure the voltage between A/T clutch pressure
control solenoid valve A connector terminals No. 1
and No. 2.
Update the PCM if it does not have the latest
software, or substitute a known-good PCM
(see page 14-11), then recheck. If the symptom/
indication goes away with a known-good PCM,
replace the original PCM.
Repair open or short in the wire between PCM
connector terminal C1 and A/T clutch pressure
control solenoid valve A, then go to step 12.
12. Clear the DTC with the HDS.
13. Test-drive the vehicle for several minutes in the
D position through all five gears.
14. Monitor the OBD status for P0962 in the DTCs/
Freeze Data in A/T Mode Menu for a pass/fail.
Troubleshooting is completed.
Return to step 6 and recheck.
Wire side of female terminals
Is ther e about 11 V as the ignition switch is tur ned
to the ON ( II) position?
Does the r esult indicate a passed?
05/06/27 17:56:37 61S6M040_140_0211
−
01
02
S6M6APPK77100090963FAAT00
−
−
−
−
−
−
−
−
DTC P0963:
2005-2006 Models
YES
NO
YES
NO
YES
NO
YES
NO
14-211
A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE A CONNECTOR
(BLK)
A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE A CONNECTOR
Problem in A/T Clutch Pressure
Control Solenoid Valve A
NOTE:
• Record all freeze data and review General
Troubleshooting Information (see page 14-8) before
you troubleshoot.
• This code is caused by an electrical circuit problem
and cannot be caused by a mechanical problem in the
transmission.
1. Clear the DTC with the HDS.
2. Check that DTC P0963 recurs.
Go to step 6.
Go to step 3.
3. Choose Clutch Pressure Control Solenoid Control
in Miscellaneous Test Menu, and test the A/T clutch
pressure control solenoid valve A with the HDS.
4. Drive with the A/T clutch pressure control solenoid
valve A at 0.2 A in Clutch Pressure Control Solenoid
Control menu.
5. Monitor the OBD status for P0963 in the DTCs/
Freeze Data in A/T Mode Menu for a pass/fail.
Go to step 6.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the A/T clutch pressure control solenoid valve A
and PCM. If the tester indicates NOT COMPLETED,
return to step 3 and recheck.
6. Turn the ignition switch OFF.
7. Disconnect the A/T clutch pressure control solenoid
valve A connector.
8. Measure A/T clutch pressure control solenoid valve
A resistance at the solenoid connector.
Go to step 9.
Replace the A/T clutch pressure control
solenoid valve A (see page 14-263), then go to step
10.
9. Check for continuity between A/T clutch pressure
control solenoid valve A connector terminal No. 2
and body ground.
Update the PCM if it does not have the latest
software, or substitute a known-good PCM
(see page 14-11), then recheck. If the symptom/
indication goes away with a known-good PCM,
replace the original PCM.
Repair open in the wire between the A/T
clutch pressure control solenoid valve A and
ground (G101), or repair poor ground (G101), then
go to step 10.
(cont’d)
Terminal side of male terminals
Wire side of female terminals
Is DT C P0963 indicated?
Does the r esult indicate a f ailed?
Is ther e 3
10
?
Is ther e continuity?
05/06/27 17:56:38 61S6M040_140_0212
−
−
YES
NO
14-212
Automatic Transmission
DTC Troubleshooting (cont’d)
10. Clear the DTC with the HDS.
11. Test-drive the vehicle for several minutes in the
D position through all five gears.
12. Monitor the OBD status for P0963 in the DTCs/
Freeze Data in A/T Mode Menu for a pass/fail.
Troubleshooting is completed.
Return to step 1 and recheck.
Does the r esult indicate a passed?
05/06/27 17:56:38 61S6M040_140_0213
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст