Acura RSX Honda Integra. Manual — part 33
01
*01
S6M6A20A14500017621FHAT02
01
02
S6M6A20A14500017601FEAT00
4-68
4-68
Cruise Control
Cruise Control Set/decel, Resume/
accel, Cancel Switch Test/
Replacement
Cruise Control Actuator Test
Terminal
Position
Set/decel (PRESSED)
Resume/accel (PRESSED)
Cancel (PRESSED)
3
2
1
B
A
A
B
SRS components are located in this area. Review the
SRS component locations (see page 23-10), and the
precautions, and procedures (see page 23-11), before
performing repairs or service.
1. Remove the two screws, then remove the switch.
2. Check for continuity between the terminals in
switch position according to the table.
• If there is continuity, and it matches the table, but
switch failure occurred on the cruise control unit
input test, check and repair the wire harness on
the switch circuit.
• If there is no continuity in one or both positions,
replace the switch.
1. Disconnect the 4P connector (A) from the cruise
control actuator (B).
2. Remove the cover (A), and check the output linkage
(B) for smooth movement.
3. Connect the battery power to the No. 2 terminal
and ground to the No. 1 terminal.
4. Check for a clicking sound from the magnetic clutch.
The output linkage should be locked.
5. If the output linkage is not locked, replace the
cruise control actuator assembly.
Terminal side of
male terminals
Terminal side of
male terminals
+
−
01
01
02
S6M6A20A14500017601KBAT10
4-69
4-69
Cruise Control Actuator/Cable
Replacement
FULL OPEN
MIDDLE
POSITION
FULL CLOSE
OUTPUT LINKAGE
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
A
B
C
B
A
6. Check the operation of the actuator motor in each
output linkage position according to the table. You
should be able to hear the motor.
Output linkage position
(
)
(
)
1. K20A3 engine: Remove the throttle cover (A), fully
open the cruise control link by hand, then remove
the cruise control cable (B) from link. Loosen the
locknut (C), and remove the cable from the bracket.
2. K20A2, K20Z1 engines: Fully open the cruise
control link by hand, then remove the cruise control
cable (A) from the link. Loosen the locknut (B), and
remove the cable from the bracket.
(cont’d)
Battery power
polarities
No. 4
Terminal
No. 3
Terminal
The
motor
runs.
The
motor
runs.
The
motor
stops.
No. 3
Terminal
No. 4
Terminal
The
motor
stops.
The
motor
runs.
The
motor
runs.
FULL
CLOSE
MIDDLE
POSITION
FULL
OPEN
03
04
05
4-70
Cruise Control
Cruise Control Actuator/Cable Replacement (cont’d)
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
A
B
3. Remove the cowl cover (see page 20-105).
4. Disconnect the 4P connector, and remove the two
bolts securing the cruise control actuator.
5. Remove the actuator cover (A), then remove the
actuator cable (B) from the cruise control actuator.
6. Remove the bracket from the cruise control
actuator.
7. Install in the reverse order of removal, and adjust
the free play at the throttle linkage after connecting
the actuator cable.
±
±
01
S6M6A20A14500017602MBAT00
01
02
S6M6A0AA14500017045FEAT00
4-71
4-71
Cruise Control Actuator Cable
Adjustment
Clutch Pedal Position Switch Test
D
C
B
A
CLUTCH PEDAL POSITION SWITCH 2P CONNECTOR
A
Terminal
Clutch Pedal
Position Switch
PRESSED
1
2
RELEASED
1. Check that the actuator cable (A) moves smoothly
with no binding or sticking.
2. Measure the amount of movement of the output
linkage (B) until the engine speed starts to increase.
At first, the output linkage should be located at the
fully closed position (C). The free play (D) should be
3.75
0.5 mm (0.15
0.02 in.).
3. If the free play is not within specifications, loosen
the locknut, and turn the adjusting nut until the free
play is as specified, then retighten the locknut.
1. Disconnect the 2P connector from the clutch pedal
position switch (A).
2. Remove the clutch pedal position switch.
3. Check for continuity between the terminals
according to the table.
• If the continuity is not as specified, replace the
clutch pedal position switch.
• If OK, install the clutch pedal position switch, and
adjust the pedal height (see page 12-6).
Terminal side of
male terminals
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст