Acura RSX Honda Integra. Manual — part 43
05
06
07
08
6-16
Cylinder Head
Cam Chain Removal (cont’d)
A
B
C
16. Loosely install the crankshaft pulley.
17. Turn the crankshaft counterclockwise to compress
the auto-tensioner.
18. Align the holes on the lock (A) and the auto-
tensioner (B), then insert a 1.2 mm (0.05 in.)
diameter pin or lock pin (P/N 14511-PNA-003) (C)
into the holes. Turn the crankshaft clockwise to
secure the pin.
19. Remove the auto-tensioner.
20. Remove the cam chain guide B.
09
01
07
S6M6A00A14674300000KCAT10
Special Tools Required
6-17
6-17
Cam Chain Installation
A
B
B
A
C
A
B
21. Remove the cam chain guide A and tensioner arm
(B).
22. Remove the cam chain.
• Holder handle 07JAB-001020A
• Holder attachment, 50 mm 07NAB-001040A
• Socket, 19 mm 07JAA-001020A or a commercially
available 19 mm socket
NOTE:
• Keep the cam chain away from magnetic fields.
• Before this procedure, check that the variable valve
timing control (VTC) actuator is locked by turning the
VTC actuator counterclockwise. If not locked, turn the
VTC actuator clockwise until it stops, then recheck it.
If it is still not locked, replace the VTC actuator.
1. Set the crankshaft to top dead center (TDC). Align
the TDC mark (A) on the crankshaft sprocket with
the pointer (B) on the engine block.
2. Set the camshafts to TDC. The punch mark (A)
marked with an arrow on the variable valve timing
control (VTC) actuator and the punch mark (B) on
the exhaust camshaft sprocket should be at the top.
Align the TDC marks (C) on the VTC actuator and
exhaust camshaft sprocket.
(cont’d)
02
03
04
05
6-18
Cylinder Head
Cam Chain Installation (cont’d)
A
B
B
A
A
B
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
3. Install the cam chain on the crankshaft sprocket
with the colored piece (A) aligned with the punch
mark (B) on the crankshaft sprocket.
4. Install the cam chain on the VTC actuator and
exhaust camshaft sprocket with the punch marks
(A) aligned with the two colored pieces (B).
5. Install the cam chain guide A and tensioner arm (B).
6. Install the auto-tensioner.
06
07
01
09
6-19
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
A
B
B
A
7. Install the cam chain guide B.
8. Remove the pin or lock pin (P/N 14511-PNA-003)
from the auto-tensioner.
9. Check the chain case oil seal for damage. If the oil
seal is damaged, replace the chain case oil seal
(see page 6-24).
10. Remove all of the old liquid gasket from the chain
case mating surfaces, bolts, and bolt holes.
11. Clean and dry the chain case mating surfaces.
12. Apply liquid gasket, P/N 08717-0004, 08718-0001,
08718-0002, 08718-0003, or 08718-0009, evenly to
the engine block mating surface on the chain case.
13. Apply liquid gasket to the engine block upper
surface contact areas (A) on the chain case and
lower block upper surface contact areas (B) on the
chain case.
14. Apply liquid gasket, P/N 08717-0004, 08718-0001,
08718-0002, 08718-0003 or 08718-0009, evenly to
the oil pan mating surface of the chain case.
NOTE: Do not install components if too much time
has passed after applying the liquid gasket (for P/N
08718-0002, no more than 4 minutes, for all others,
no more than 5 minutes). Instead, remove the old
residue and reapply the liquid gasket.
(cont’d)
Apply liquid gasket
along the broken line.
Apply liquid gasket
along the broken line.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст