Acura ILX (2021 year). Manual in english — page 9
142
uu
Operating the Switches Around the Steering Wheel
u
Turn Signals
Co
ntrols
Turn Signals
The turn signals can be used when the power
mode is in ON.
■
(A): Turn signal
Push the lever up or down based on the
direction you want to turn, and the turn signal
will blink.
■
(B): One-touch turn signal
When you lightly push the lever up or down
and release it, the turn signal will blink 3
times.
1
The turn signal indicator on the instrument panel will
blink when the external turn signal blinks.
2
P. 72
(A)
(A)
(B)
(B)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
143
uu
Operating the Switches Around the Steering Wheel
u
Light Switches
Continued
Co
ntrols
Light Switches
Rotating the light switch turns the lights on
and off, regardless of the power mode
setting.
■
High beams
Push the lever forward until you hear a click.
■
Low beams
When in high beams, pull the lever back to
return to low beams.
■
Flashing the high beams
Pull the lever back, and release it.
■
Lights off
Turn the lever to
OFF
either when:
•
The transmission is in
(
P
.
•
The parking brake is applied.
To turn the lights on again, turn the lever to
OFF
to cancel the lights off mode. Even if you
do not cancel the lights off mode, the lights
come on automatically when:
•
The transmission is taken out of
(
P
and the
parking brake is released.
•
The vehicle starts to move.
■
Manual Operation
1
If you leave the power mode in VEHICLE OFF (LOCK)
while the lights are on, a chime sounds when the
driver’s door is opened.
When the lights are on, the lights on indicator in the
instrument panel will be on.
2
P. 78
Do not leave the lights on when the engine is off
because it will cause the battery to discharge.
If you sense that the level of the headlights is
abnormal, have the vehicle inspected by a dealer.
High Beams
Flashing the high beams
Low Beams
Turns on parking, side marker,
tail, and rear license plate lights
Turns on headlights, parking,
side marker, tail, and rear
license plate lights
-------------------------------------------------------------------------------------------------------------------------------------------------------------
uu
Operating the Switches Around the Steering Wheel
u
Light Switches
144
Co
ntrols
Automatic lighting control can be used when
the power mode is in ON.
When the light switch is in
AUTO
, the
headlights and other exterior lights will switch
on and off automatically depending on the
ambient brightness.
The headlights come on when you unlock a
door in dark areas with the headlight switch in
AUTO
.
u
Once you lock the door, the headlights
will go off.
■
Automatic Operation (automatic lighting control)
1
Automatic Operation (automatic lighting control)
We recommend that you turn on the lights manually
when driving at night, in a dense fog, or in dark areas
such as long tunnels or parking facilities.
The light sensor is in the location shown below.
Do not cover this light sensor with anything;
otherwise, the automatic lighting system may not
work properly.
Light Sensor
Models with automatic
intermittent wipers
Models without automatic
intermittent wipers
Light Sensor
-------------------------------------------------------------------------------------------------------------------------------------------------------------
145
uu
Operating the Switches Around the Steering Wheel
u
Light Switches
Co
ntrols
The headlights automatically come on when the wipers are used several times within
a certain number of intervals with the headlight switch in
AUTO
.
The headlights automatically go off a few minutes later if the wipers are stopped.
The headlights, all other exterior lights, and the instrument panel lights turn off 15
seconds after you set the power mode to VEHICLE OFF (LOCK), take the remote with
you, and close the driver's door.
If you set the power mode to VEHICLE OFF (LOCK) with the headlight switch on, but
do not open the door, the lights turn off after 10 minutes (3 minutes, if the switch
is in the
AUTO
position).
The lights turn on again when you unlock or open the driver's door. If you unlock
the door, but do not open it within 15 seconds, the lights go off. If you open the
driver's door, you will hear a reminder chime alerting you that the lights are on.
■
Headlight Integration with Wiper
■
Automatic Lighting Off Feature
1
Automatic Operation (automatic lighting control)
You can adjust the auto light sensitivity as follows:
2
Customized Features
P. 99, 315
Setting
The exterior lights come on
when the ambient light is at
Max
High
Mid
Low
Min
U.S. models
Bright
Dark
1
Headlight Integration with Wiper
This feature activates while the headlights are off in
AUTO
.
The instrument panel brightness does not change
when the headlights come on.
At dark ambient light levels, the automatic lighting
control feature turns on the headlights, regardless of
the number of wiper sweeps.
1
Automatic Lighting Off Feature
You can change the headlight auto off timer setting.
2
Customized Features
P. 99, 315
-------------------------------------------------------------------------------------------------------------------------------------------------------------
146
uu
Operating the Switches Around the Steering Wheel
u
Fog Lights
*
Co
ntrols
Fog Lights
*
When the low beam headlights are on, turn
the fog light switch on to use the fog lights.
Daytime Running Lights
The parking/daytime running lights come on when the following conditions have
been met:
•
The power mode is in ON.
•
The headlight switch is in
AUTO
.
•
The parking brake is released.
The lights remain on even if you set the parking brake.
Setting the power mode to VEHICLE OFF (LOCK) will turn off the daytime running
lights.
The daytime running lights are off once the headlight switch is turned on, or when
the headlight switch is in
AUTO
and it is getting darker outside.
Fog Light Switch
* Not available on all models
-------------------------------------------------------------------------------------------------------------------------------------------------------------
147
uu
Operating the Switches Around the Steering Wheel
u
Auto High-Beam
Continued
Co
ntrols
Auto High-Beam
The front sensor camera detects the light sources ahead of the vehicle such as the
lights of a preceding or oncoming vehicle, or street lights. When you are driving at
night, the system automatically switches the headlights between low beam and high
beam depending on the situation.
When all of the following conditions have been met, the auto high-beam indicator
comes on and the auto high-beam is activated.
•
The power mode is in ON.
•
The light switch is in
AUTO
.
•
The lever is in the low beam position.
•
The headlights have been automatically
activated.
•
It is dark outside the vehicle.
If the auto high-beam indicator does not come on even when all the conditions have
been met, carry out the following procedure and the indicator will come on.
•
Pull the lever toward you for flashing the high beams then release it while driving.
1
The auto high-beam system does not always operate
in every situation. This system is just for assisting the
driver. Always observe your surroundings and switch
the headlights between high beam and low beam
manually if necessary.
If you find the timing of beam changes inconvenient
for driving, change the headlight beams manually.
The range and the distance at which the camera can
recognize varies depending on conditions
surrounding your vehicle.
Regarding the handling of the camera mounted to
the inside of the windshield, refer to the following.
2
P. 493
For the auto high-beam to work properly:
•
Do not place an object that reflects light on the
dashboard.
•
Keep the windshield around the camera clean.
•
When cleaning the windshield, be careful not to
apply the windshield cleanser to the camera lens.
•
Do not attach an object, sticker or film to the area
around the camera.
•
Do not touch the camera lens.
If the camera receives a strong impact, or repairing of
the area near the camera is required, consult a dealer.
■
How to Use the Auto High-Beam
Front Sensor Camera
Auto High-Beam
Indicator
Light Switch
-------------------------------------------------------------------------------------------------------------------------------------------------------------
uu
Operating the Switches Around the Steering Wheel
u
Auto High-Beam
148
Co
ntrols
■
Automatic switching between high-beam and low-beam
When auto high-beam is active, the headlights switch between high beam and low
beam based on the following conditions.
■
Manual switching between high-beam and low-beam
If you want to manually switch the headlights between high beam and low beam,
follow either of the procedures below. Note that when you do this, the auto high-
beam indicator will turn off and the auto high-beam will be deactivated.
Using the lever:
Pull the lever toward you for flashing the high beams then release it within about
one second while driving.
u
To reactivate the auto high-beam, pull the lever toward you for flashing the
high beams then release it while driving. The auto high-beam indicator will
come on.
Using the light switch:
Turn the light switch to
.
u
To reactivate the auto high-beam, turn the light switch to
AUTO
when the
lever is in the low beam position, the auto high-beam indicator will come on.
Switching to high beam:
Switching to low beam:
All of the following conditions must
be met before the high beams turn
on.
●
Your vehicle speed is 45mph (72
km/h) or more.
●
There are no preceding or
oncoming vehicle with headlights
or taillights turned on.
●
There are few street lights on the
road ahead.
One of the following conditions
must be met before the low beams
turn on.
●
Your vehicle speed is 30 mph (48
km/h) or less.
●
There is a preceding or oncoming
vehicle with headlights or
taillights turned on.
●
There are many street lights on
the road ahead.
1
In the following cases, the auto high-beam system
may not switch the headlights properly or the
switching timing may be changed. In case of the
automatic switching operation does not fit for your
driving habits, please switch the headlights manually.
•
The brightness of the lights from the preceding or
oncoming vehicle is intense or poor.
•
Visibility is poor due to the weather (rain, snow,
fog, windshield frost, etc.).
•
Surrounding light sources, such as street lights,
electric billboards and traffic lights are illuminating
the road ahead.
•
The brightness level of the road ahead constantly
changes.
•
The road is bumpy or has many curves.
•
A vehicle suddenly appears in front of you, or a
vehicle in front of you is not in the preceding or
oncoming direction.
•
Your vehicle is tilted with a heavy load in the rear.
•
A traffic sign, mirror, or other reflective object
ahead is reflecting strong light toward the vehicle.
•
The oncoming vehicle frequently disappears under
roadside trees or behind median barriers.
•
The preceding or oncoming vehicle is a motorcycle,
bicycle, mobility scooter, or other small vehicle.
The auto high-beam system keeps the headlight low
beam when:
•
Windshield wipers are operating.
•
The camera has detected a dense fog.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
149
uu
Operating the Switches Around the Steering Wheel
u
Auto High-Beam
Co
ntrols
You can turn the auto high-beam system off. If you want to turn the system off or
on, set the power mode to ON, then carry out the following procedures while the
vehicle is stationary.
To turn the system off:
With the light switch is in
AUTO
, pull the lever
toward you and hold it for at least 40 seconds.
After the auto high-beam indicator light blinks
twice, release the lever.
To turn the system on:
With the light switch is in
AUTO
, pull the lever
toward you and hold it for at least 30 seconds.
After the auto high-beam indicator light blinks
once, release the lever.
■
How to Turn Off the Auto High-Beam
1
If the
Some Driver Assist Systems Cannot
Operate: Camera Temperature Too High
message
appears:
•
Use the climate control system to cool down the
interior and, if necessary, also use defroster mode
with the airflow directed toward the camera.
•
Start driving the vehicle to lower the windshield
temperature, which cools down the area around
the camera.
If the
Some Driver Assist Systems Cannot
Operate: Clean Front Windshield
message
appears:
•
Park your vehicle in a safe place, and clean the
windshield. If the message does not disappear after
you have cleaned the windshield and driven for a
while, have your vehicle checked by a dealer.
1
How to Turn Off the Auto High-Beam
If you turn the auto high-beam system off, the system
does not operate until you turn the system on.
Park in a safe place before turning the system off or
on.
AUTO
Position
-------------------------------------------------------------------------------------------------------------------------------------------------------------
150
uu
Operating the Switches Around the Steering Wheel
u
Wipers and Washers
Co
ntrols
Wipers and Washers
The windshield wipers and washers can be
used when the power mode is in ON.
■
MIST
The wipers run at high speed until you release
the lever.
■
Wiper switch (OFF, INT
*1
/AUTO
*2
, LO,
HI)
Move the lever up or down to change the
wiper settings.
■
Adjusting wiper operation
*
Turn the adjustment ring to adjust the wiper
operation.
■
Washer
Sprays while you pull the lever toward you.
When you release the lever for more than one
second, the spray stops, the wipers sweep two
or three more times to clear the windshield,
then stop.
*1: Models with manual intermittent operation
*2: Models with automatic intermittent operation
■
Windshield Wipers/Washers
1
NOTICE
Do not use the wipers when the windshield is dry.
The windshield will get scratched, or the rubber
blades will get damaged.
NOTICE
Turn the washers off if no washer fluid comes out.
The pump may get damaged.
The wiper motor may stop motor operation
temporarily to prevent an overload. Wiper operation
will return to normal within a few minutes, once the
circuit has returned to normal.
If the vehicle speeds up while the wipers are
operating intermittently, the length of the wipe
interval shortens.
When the vehicle speeds up, the wiper operation’s
shortest delay setting ( ) and the
LO
setting become
the same.
NOTICE
In cold weather, the blades may freeze to the
windshield.
Operating the wipers in this condition may damage
the wipers. Use the defogger to warm the
windshield, then turn the wipers on.
Models with intermittent time adjustment ring
Intermittent Time
Adjustment Ring
*
MIST
INT
*1
/
AUTO
*2
OFF
LO
: Low speed wipe
HI
: High speed wipe
Pull to
use
washer.
Lower speed, fewer sweeps
Higher speed, more sweeps
* Not available on all models
-------------------------------------------------------------------------------------------------------------------------------------------------------------
151
uu
Operating the Switches Around the Steering Wheel
u
Wipers and Washers
Co
ntrols
When you push the lever down to
AUTO
, the
windshield wipers sweep once, and go into
the automatic mode.
The wipers operate intermittently, at low
speed, or at high speed and stops in
accordance with the amount of rainfall the
rainfall sensor detects.
■
AUTO sensitivity adjustment
When the wiper function is set to
AUTO
, you
can adjust the sensitivity of the rainfall sensor
(using the adjustment ring) so that wipers will
operate in accordance with your preference.
Sensor sensitivity
■
Automatic Intermittent Wipers
*
1
If the wipers stop operating due to an obstacle such
as the build-up of snow, park the vehicle in a safe
place.
Rotate the wiper switch to
OFF
, and set the power
mode to ACCESSORY or VEHICLE OFF (LOCK), then
remove the obstacle.
1
The rainfall sensor is in the location shown below.
NOTICE
AUTO
should always be turned
OFF
before the
following situations in order to prevent severe
damage to the wiper system:
•
Cleaning the windshield
•
Driving through a car wash
•
No rain present
Rainfall Sensor
Adjustment Ring
Low sensitivity
High sensitivity
* Not available on all models
-------------------------------------------------------------------------------------------------------------------------------------------------------------
152
uu
Operating the Switches Around the Steering Wheel
u
Brightness Control
Co
ntrols
Brightness Control
When the power mode is in ON, you can use
the brightness control knob to adjust
instrument panel brightness.
Brighten:
Turn the knob to the right.
Dim:
Turn the knob to the left.
You will hear a beep when the brightness
reaches minimum or maximum. Several
seconds after adjusting the brightness, you
will be returned to the previous display.
■
Brightness level indicator
The brightness level is shown on the display
while you are adjusting it.
1
The brightness of the instrument panel will be
reduced when the following conditions:
•
The power mode is in ON.
•
The light switch is in any position other than
OFF
and it is dark outside.
The brightness can be set differently for when the
exterior lights are on, and when they are off.
Control Knob
-------------------------------------------------------------------------------------------------------------------------------------------------------------
153
uu
Operating the Switches Around the Steering Wheel
u
Rear Defogger/Heated Door Mirror Button
Co
ntrols
Rear Defogger/Heated Door Mirror Button
Press the rear defogger and heated door
mirror button to defog the rear window and
mirrors when the power mode is in ON.
The rear defogger and heated door mirrors
automatically switch off after 10-30 minutes
depending on the outside temperature.
However, if the outside temperature is 32°F
(0°C) or below, it does not automatically
switch off.
Adjusting the Steering Wheel
The steering wheel height and distance from your body can be adjusted so that you
can comfortably grip the steering wheel in an appropriate driving posture.
1.
Pull the steering wheel adjustment lever up.
u
The steering wheel adjustment lever is
under the steering column.
2.
Move the steering wheel up or down, and
in or out.
u
Make sure you can see the instrument
panel gauges and indicators.
3.
Push the steering wheel adjustment lever
down to lock the steering wheel in position.
u
After adjusting the position, make sure
you have securely locked the steering
wheel in place by trying to move it up,
down, in, and out.
1
Rear Defogger/Heated Door Mirror Button
This system consumes a lot of power, so turn it off
when the window has been defogged.
Also, do not use the system for a long time while the
engine is idling. This may weaken the battery, making
it difficult to start the engine.
When the power mode is set to ON and the outside
temperature is below 41°F (5°C), the heated door
mirror may automatically activate for 10 minutes.
1
3
WARNING
Adjusting the steering wheel position while
driving may cause you to lose control of the
vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the
vehicle is stopped.
To adjust
To lock
Lever
-------------------------------------------------------------------------------------------------------------------------------------------------------------
154
uu
Operating the Switches Around the Steering Wheel
u
Driving Position Memory System
*
Co
ntrols
Driving Position Memory System
*
You can store two driver’s seat (except for power lumbar) positions with the driving
position memory system.
When you unlock and open the driver’s door with a remote transmitter, or keyless
access system, the seat adjust automatically to one of the two preset positions.
When you enter the vehicle, the multi-information display briefly shows you which
remote transmitter you used to unlock the vehicle.
•
DRIVER 1
transmitter is linked to memory button 1.
•
DRIVER 2
transmitter is linked to memory button 2.
1
Driving Position Memory System
Using the information screen or multi-information
display, you can disable the automatic seat
adjustment function.
2
Customized Features
P. 99, 315
DRIVER 1
DRIVER 2
* Not available on all models
-------------------------------------------------------------------------------------------------------------------------------------------------------------
155
uu
Operating the Switches Around the Steering Wheel
u
Driving Position Memory System
*
Co
ntrols
1.
Set the power mode to ON. Adjust the
driver’s seat to the desired position.
2.
Press the
SET
button.
u
You will hear the beep, and the memory
button indicator light will blink.
3.
Press and hold memory button
(
1
or
(
2
within five seconds of pressing the
SET
button.
u
Once the seat positions have been
memorized, the indicator light on the
button you pressed stays on and you will
hear the double-beep.
1.
Put the transmission into
(
P
.
2.
Apply the parking brake.
3.
Press a memory button (
(
1
or
(
2
).
u
You will hear the beep, and the indicator
light will blink.
The seat will automatically move to the
memorized position. When it has finished
moving, you will hear the beep, and the
indicator light stays on.
■
Storing a Position in Memory
1
After you press the
SET
button, the storing operation
will be canceled when:
•
You do not press the memory button within five
seconds.
•
You readjust the seat position before the double-
beep.
•
You set the power mode to any position except
ON.
SET
Button
Memory Button 1
Memory Button 2
■
Recalling the Stored Position
1
The seat will stop moving if you:
•
Press the
SET
button or memory button
(
1
or
(
2
.
•
Adjust the seat position.
•
Put the transmission into a position other than
(
P
.
Memory Buttons
-------------------------------------------------------------------------------------------------------------------------------------------------------------
156
Co
ntrols
Mirrors
Interior Rearview Mirror
Adjust the angle of the rearview mirror when you are sitting in the correct driving
position.
Flip the tab to switch the position.
The night position will help to reduce the glare
from headlights behind you when driving
after dark.
When you are driving after dark, the
automatic dimming rearview mirror reduces
the glare from headlights behind you, based
on inputs from the mirror sensor. This feature
is always active.
■
Rearview Mirror with Day and Night Positions
*
1
Keep the inside and outside mirrors clean and
adjusted for best visibility.
Adjust the mirrors before you start driving.
2
P. 158
Daytime
Position
Night
Position
■
Automatic Dimming Rearview Mirror
*
1
Automatic Dimming Rearview Mirror
The auto dimming function cancels when the
transmission is in
(
R
.
Sensor
* Not available on all models
-------------------------------------------------------------------------------------------------------------------------------------------------------------
157
uu
Mirrors
u
Power Door Mirrors
Co
ntrols
Power Door Mirrors
You can adjust the door mirrors when the
power mode is in ON.
■
Mirror position adjustment
L/R selector switch:
Select the left or right
mirror. After adjusting the mirror, return the
switch to the center position.
Mirror position adjustment switch:
Press
the switch left, right, up, or down to move the
mirror.
Selector Switch
Adjustment Switch
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст