DAF 95XF. Manual — part 619
8
LEADING REAR AXLE 09N044 (FTP-TYPE VEHICLES)
Inspection and adjustment
95XF series
2-2
7. Turn back the hub nut until the split pin can
be fitted. Fit a new split pin.
Note:
There are 2 split pin holes in the axle
journal. Select the split pin hole where the
hub nut needs to be turned back least.
8. Check the wheel bearing play. Check the
bearings for wear if the wheel bearing play
is still too large after adjustment.
9. Fit the hub cap. Tighten the hub cap to the
specified torque using the special tool
(DAF no. 1329498). See “Technical data”.
10. Adjust the brakes.
2.2 CHECKING THE HUB AND WHEEL BEARINGS
1. Check the bearings for damage at the
following points:
-
the roller bearing races,
-
the bearing cage,
-
the raceways of the inner and outer
race.
If damage is found, the entire bearing (inner
race/bearing cage and outer race) should
be replaced.
2. If the outer bearing race is loose in the hub
or has turned in the hub, the hub should be
replaced.
3. Check the axle journal screw thread, the
bearing surfaces of the inner bearing races
and the running surface of the seal for
damage.
7
200424
8
95XF series
Removal and installation
LEADING REAR AXLE 09N044 (FTP-TYPE VEHICLES)
3-1
3. REMOVAL AND INSTALLATION
3.1 REMOVAL AND INSTALLATION, WHEEL HUB
Removing the wheel hub
1. Remove the hub cap (5) using special tool
(DAF no. 1329498).
2. Lift the leading rear axle and support it
properly.
3. Remove the split pin (4) and the hub nut (3).
4. Remove the outer wheel bearing (2).
5. Remove the hub (1) with the wheel.
Installing the wheel hub
1. Remove the grease from the hub (1).
2. Clean the bearings and liberally re-grease
the outer bearing races and bearing cages.
3. Lubricate the space between the wheel
bearings with new grease.
4. Install the hub with the wheel.
5. Install the outer wheel bearing (2).
6. Fit the hub nut (5).
7. Adjust the wheel bearing play, see chapter
“Inspection and adjustment”.
8. Fit a new split pin (4).
9. Lower the leading rear axle.
10. Remove the hub cap (5) using special tool
(DAF no. 1329894). Tighten the hub cap to
the specified torque, see “Technical data”.
11. Adjust the brakes.
A8 00 430
1
2
3 4
5
7
200424
8
LEADING REAR AXLE 09N044 (FTP-TYPE VEHICLES)
Removal and installation
95XF series
3-2
3.2 REMOVAL AND INSTALLATION, HUB OIL SEAL
Removing the hub oil seal
1. Remove the hub from the axle journal.
2. Drill two holes into the seal and screw the
special tool (B) (DAF No. 0484899) into the
seal. Pull the seal from the hub using the
special tool (A) (DAF No. 0694928).
Installing the hub oil seal
1. Check the seal chamber for damage.
2. For installation of the hub seal use special
tool (DAF no. 1329497). Press the seal into
the hub.
3. Apply a little grease to the sealing lips of the
seal.
4. Install the hub on the axle journal.
A
B
A8 00 432
7
200424
8
95XF series
Removal and installation
LEADING REAR AXLE 09N044 (FTP-TYPE VEHICLES)
3-3
3.3 REMOVAL AND INSTALLATION, WHEEL BEARINGS
Removing wheel bearings
1. Remove the hub (3) from the axle.
2. Remove the hub seal (6).
3. Remove the bearing cages (1) and (5).
4. If the wheel bearings should be replaced,
the outer bearing races (2) and (4) can be
tapped from the hub (3) using a copper
driving tool.
Installing wheel bearings
1. Clean the bearings and check them for
damage.
2. Use a driving tool and a hydraulic press to
install the new outer bearing races (2) and
(4) into the hub (3). Check that the outer
races (2) and (4) are pressed into the hub
(3) as far as the stop.
3. Apply an ample quantity of new grease to
the outer races (2) and (4) and the bearing
cages (1) and (5).
4. Lubricate the space between the wheel
bearings with new grease.
5. Fit a new hub seal (6).
6. Install the hub (3).
1
2
3
4
5
6
A8 00 431
7
200424
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст