DAF 95XF. Manual — part 564
8
TECHNICAL DATA
Contents
95XF series
2
0
200424
0
8
95XF series
Single rear axle 1347
TECHNICAL DATA
1-1
1. SINGLE REAR AXLE 1347
1.1 GENERAL
Sealant for differential
Mating surface and around bolt holes of axle
body
Loctite 5910
Sealant for axle shaft
Mating surface of axle shaft flange
Loctite 5910
Wheel bearings
Wheel bearing play
0.025 - 0.25 mm
ABS sensor ring
Axial end play
max. 0.2 mm
Trailing axle lifting height
Minimum trailing axle lifting height
100 mm
Driven axle caster
FAG
3.5_
FAS (11/7 ratio)
(1)
3.5_
FAS (10/10 ratio)
(1)
4_
Other
4.5_
Note:
(1)
With a lowered trailing axle
200424
8
TECHNICAL DATA
Single rear axle 1347
95XF series
1-2
1.2 TIGHTENING TORQUES
The tightening torques stated in this section are
different from the standard tightening torques
stated in the overview of the standard tightening
torques. Any other threaded connections that
are not specified must therefore be tightened to
the torque stated in the overview of standard
tightening torques.
When attachment bolts and nuts are replaced, it
is important that - unless stated otherwise -
these bolts and nuts are of exactly the same
length and property class as the ones removed.
Differential
Drive flange attachment nut
1250 Nm
(1)
Differential lock cover attachment bolts
-
if M8 8.8
23 Nm
-
if M8 10.9
30 Nm
M12 attachment bolts of pinion housing cover
70 Nm
(2)
Attachment bolts, differential to axle housing
-
if M16 8.8
195 Nm
(2)
-
if M16 10.9
260 Nm
(2)
Torx plug (level check/filler and drain plug)
85 Nm
Hub
Lock nut (outer nut)
560 Nm
Axle shaft attachment bolts
-
if M16 8.8
195 Nm
-
if M16 10.9
260 Nm
Torx plug, wheel hub
85 Nm
Note:
(1)
Secure with Loctite 262
(2)
Secure with Loctite 572
1.3 FILLING CAPACITIES
Differential
Minimum caster
Maximum caster
Filling capacity
approx. 21.6 litres
approx. 23.3 litres
Hub
Oil capacity, per hub
0.9 litres
0
200424
0
8
95XF series
Single rear axle 1354
TECHNICAL DATA
2-1
2. SINGLE REAR AXLE 1354
2.1 GENERAL
Sealant for differential
Mating face and around stud bolts of banjo
housing
Loctite 5910
Wheel bearings
Wheel bearing pre-load:
frictional force without hub seal
30 - 62 N
(1)
ABS sensor ring
Axial end play
max. 0.2 mm
Trailing axle lifting height
Minimum trailing axle lifting height
100 mm
Driven axle caster
FAG
3.5_
FAS (11/7 ratio)
(2)
3.5_
FAS (10/10 ratio)
(2)
4_
FAV
2_
Other
4.5_
Note:
(1)
Measured at the circumference of the hub
(2)
With a lowered trailing axle
200424
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст