DAF 95XF. Manual — part 565
8
TECHNICAL DATA
Single rear axle 1354
95XF series
2-2
2.2 TIGHTENING TORQUES
The tightening torques stated in this section are
different from the standard tightening torques
stated in the overview of the standard tightening
torques. Any other threaded connections that
are not specified must therefore be tightened to
the torque stated in the overview of standard
tightening torques.
When attachment bolts and nuts are replaced, it
is important that - unless stated otherwise -
these bolts and nuts are of exactly the same
length and property class as the ones removed.
Differential
Drive flange attachment nut
1325 Nm
(1)
Lock nut of differential lock cylinder
80 Nm
Attachment bolts, differential to axle housing
-
if M16 8.8
195 Nm
(2)
-
if M16 10.9
260 Nm
(2)
Torx plug (level check/filler and drain plug)
85 Nm
Hub
Hub nut
2125 Nm
Attachment bolts, locking plate
-
if M8 8.8
23 Nm
(3)
-
if M8 10.9
30 Nm
(3)
Planet-gear unit attachment nuts
45 Nm
Hub cap attachment bolts
-
if M8 8.8
23 Nm
-
if M8 10.9
30 Nm
Torx plug (level check/filler and drain plug)
85 Nm
Note:
(1)
Secure with Loctite 262
(2)
Secure with Loctite 572
(3)
Secure with Loctite 243
2.3 FILLING CAPACITIES
Differential
Filling capacities
approx. 16.5 litres
Hub
Oil capacity, per hub
2.0 litres
0
200424
0
8
95XF series
Tandem rear axle 1355 T
TECHNICAL DATA
3-1
3. TANDEM REAR AXLE 1355 T
3.1 GENERAL
Sealants for differential
Mating face of banjo housing
Loctite 5910
Attachment bolt and nut flanges, differential to
axle housing
Loctite 5910
Input shaft bearing house cover
Loctite 5910
Wheel bearings
Wheel bearing pre-load:
frictional force without hub seal
30 - 62 N
(1)
ABS sensor ring
Axial end play
max. 0.2 mm
Driven axle caster
Caster
5_
Note:
(1)
Measured at the circumference of the hub
Differential lock adjustment
Selector shaft adjusting screw 0.1 mm under the
mating surface of the differential housing with
fully engaging claws.
200424
8
TECHNICAL DATA
Tandem rear axle 1355 T
95XF series
3-2
3.2 TIGHTENING TORQUES
The tightening torques stated in this section are
different from the standard tightening torques
stated in the overview of the standard tightening
torques. Any other threaded connections that
are not specified must therefore be tightened to
the torque stated in the overview of standard
tightening torques.
When attachment bolts and nuts are replaced, it
is important that - unless stated otherwise -
these bolts and nuts are of exactly the same
length and property class as the ones removed.
Differential
Drive flange attachment nut
1385 Nm
(1)
Differential lock cover attachment bolts
-
if M8 8.8
23 Nm
-
if M8 10.9
30 Nm
Attachment bolts, differential to axle housing
-
M12 attachment bolts
-
if M12 8.8
75 Nm
(2)
-
if M12 10.9
110 Nm
(2)
-
M14 12.9 attachment bolts
200 Nm
(2)
Attachment bolts, input shaft bearing cover
50 Nm
Torx plug (level check/filler and drain plug)
85 Nm
Hub
Hub nut
2125 Nm
Attachment bolts, locking plate
-
if M8 8.8
23 Nm
(3)
-
if M8 10.9
30 Nm
(3)
Planet-gear unit attachment nuts
45 Nm
Hub cap attachment bolts
-
if M8 8.8
23 Nm
-
if M8 10.9
30 Nm
Torx plug (level check/filler and drain plug)
85 Nm
Note:
(1)
Secure with Loctite 262
(2)
Secure with Loctite 572
(3)
Secure with Loctite 243
0
200424
0
8
95XF series
Tandem rear axle 1355 T
TECHNICAL DATA
3-3
3.3 FILLING CAPACITIES
Differential
Filling capacity 1
st
axle
approx. 18.0 litres
Filling capacity 2
nd
axle
approx. 13.0 litres
Hub
Oil capacity, per hub
2.0 litres
200424
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст