DAF LF45, LF55 Series. Manual — part 471
©
200436
3-35
Removal and installation
BRAKE SYSTEM AND COMPONENTS
ΛΦ45/55 series
6
4
8.
Force the bearing bushes out of the brake
calliper using the ejector tool, special tool set
(DAF no. 1451974); the attachment side for
the brake cylinder must point upwards.
Installation, bearing bushes
1.
Clean the bearing bush bores.
2.
Force a bearing bush into the bearing bush
bore (A) using the forcing tool, special tool
set (DAF no. 1451974) for the long guide
bush.
3.
Force a bearing bush into the bearing bush
bore (B) using the forcing tool, special tool
set (DAF no. 1451974), for the short guide
bush.
4.
Apply the prescribed lubricant to the bearing
bushes and the space between them. See
"Technical data".
5.
Force a bearing bush into the bearing bush
bore (C) using the forcing tool, special tool
set (DAF no. 1451974), for the guide bush.
6.
Apply the lubricant provided to the bearing
bush.
7.
Position the new guide bush dust covers in
the brake calliper.
8.
Apply the lubricant provided to the guide
bushes.
9.
Position the guide bushes in the brake
calliper.
10. Position the guide bush dust covers over the
guide bushes.
11. Position the brake carrier on the brake
calliper.
12. Insert the new Allen screws into the brake
calliper and tighten to the specified torque.
See "Technical data".
4
4
R600592
R600593
L
1
L
2
A
B
R600603
L
3
C
BRAKE SYSTEM AND COMPONENTS
3-36
©
200436
Removal and installation
4
ΛΦ45/55 series
6
Note:
To prevent damage to the guide bush dust
covers, the Allen screw of the long guide bush
must be tightened first.
13. Check the brake carrier guide and the brake
calliper in relation to each other.
14. Position the new covers in the brake calliper.
15. Mount the brake calliper on the hub.
16. Mount the brake cylinder on the brake
calliper.
©
200436
3-37
Removal and installation
BRAKE SYSTEM AND COMPONENTS
ΛΦ45/55 series
6
4
3.19 REMOVING AND INSTALLING BRASS BEARING BUSH OF BRAKE
CALLIPER, KNORR SB7000 VERSION
Removing brass bearing bush
1.
Remove the brake calliper.
2.
Remove washer (1).
3.
Remove guide bush (2).
4.
Remove the bellows (3).
5.
Remove the brass bearing bush (4) using a
bearing bush extractor (5), special tool set
(DAF no. 1329494).
6.
Clean the bearing bush bore.
Fitting brass bearing bush
1.
Fit the new brass bearing bush (4) using
bearing bush extractor 5,special tool set
(DAF no. 1329494).
2
3
1
R600723
R600727
4
5
R600728
4
5
BRAKE SYSTEM AND COMPONENTS
3-38
©
200436
Removal and installation
4
ΛΦ45/55 series
6
2.
Lock the bearing bush (4) in the brake
calliper (5) using a locking tool (6),special
tool set (DAF no. 1329494).
After the first locking operation, release the
locking tool, rotate 60
and lock normally.
3.
Check the bearing bush for burrs.
4.
Apply lubricant to the bearing bush. See
"Technical data".
5.
Fit the bellows (3).
6.
Install the guide bush (2).
7.
Install the washer (1).
6
5
4
R600726
2
3
1
R600723
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст