DAF CF65, CF75, CF85 Series . Manual — part 224
©
200324
4-11
Removal and installation
PE ENGINE
CF65/75/85 series
2
5
19. If applicable, fit the coolant filter to the
coolant pipe.
20. Fit the heat shields of the exhaust manifold
and tighten the attachment bolts to the
specified torque. See "Technical data".
21. If applicable, fit the air-conditioning bracket.
22. Adjust the V-belt tension of the air-
conditioning compressor.
23. Connect the compressor pipe from the
charge pipe to the compressor.
24. Connect the inlet pipe between the
turbocharger and air cooler.
PE ENGINE
4-12
©
200324
Removal and installation
5
CF65/75/85 series
2
4.9 REMOVAL AND INSTALLATION, AIR COMPRESSOR
Removing the air compressor
1.
Drain the coolant.
2.
Remove the oil filler pipe (5).
3.
Disconnect the service pipe from the air
dryer (8).
4.
Remove the coolant connections (1).
5.
Disconnect the air pipes (2 and 3).
6.
Disconnect the lubricating oil pipe (4).
7.
Remove the mounting bracket at the back of
the compressor (7).
8.
Remove the attachment bolts from the timing
cover.
Note:
If the vehicle is equipped with air-
conditioning, the air-conditioning
compressor V-belt must be disconnected to
enable removal of the tensioner.
9.
Remove the compressor from the timing
case. Remove the O-ring from the
compressor housing.
Installing the air compressor
1.
Fit a new O-ring to the compressor housing
and fit the compressor to the timing case.
2.
Fit the air compressor attachment bolts.
Tighten the attachment bolts to the specified
torque. See "Technical data".
Note:
If the vehicle is equipped with air-
conditioning, the tensioner of the air-
conditioning compressor must be fitted and
the V-belt tension adjusted.
M200763
4
7
4
8
5
2
1
3
©
200324
4-13
Removal and installation
PE ENGINE
CF65/75/85 series
2
5
3.
Fit the mounting bracket (7) at the back of the
compressor. Tighten the attachment bolts to
the specified torque. See "Technical data".
4.
Fit the service pipe (8).
5.
Fit the lubricating oil pipe.
6.
Fit the air pipes (2 and 3).
7.
Fit the coolant pipes (1).
8.
Fill the cooling system.
M200763
4
7
4
8
5
2
1
3
PE ENGINE
4-14
©
200324
Removal and installation
5
CF65/75/85 series
2
4.10 REMOVAL AND INSTALLATION, STEERING PUMP
Removing the steering pump
1.
Clean the steering pump and the
surrounding area.
2.
Remove the suction and delivery pipes from
the steering pump. Collect the steering oil
released from the system.
3.
Immediately plug the openings in the pump
and hoses to prevent dirt entering the
system.
4.
Remove the two attachment bolts in the
timing cover and take the pump from the
timing case.
5.
Check the gear for wear or damage.
6.
Remove the O-ring.
Installing the steering pump
1.
Fit a new O-ring.
2.
Fit the steering pump and tighten the
attachment bolts to the specified torque. See
"Technical data".
3.
Install the suction and delivery pipes of the
steering pump. Fit the banjo bolts. Tighten
the banjo bolts to the specified torque. See
"Technical data".
4.
Fill the oil reservoir with the specified oil. See
"Fluids and lubricants" specifications
manual.
5.
Bleed the steering system.
6.
Check the pipes for leaks.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст