DAF CF65, CF75, CF85 Series . Manual — part 1059
©
200424
2-5
Removal and installation
TRAILING AXLES
ΧΦ65/75/85 series
8
8
7.
Install the guide sleeve (A), which is part of
the special tool set (DAF no. 1329496), on
the axle journal.
8.
Attach the wheel hub unit (5) securely to a
movable lifting device.
9.
Slide the wheel hub unit (5) from the axle
journal using the lifting device.
Take care that the wheel hub unit (5) does
not rest on the guide bush (A) as the latter is
not strong enough to take the weight of the
wheel hub unit (5).
10. Remove the O-ring (6) from the wheel hub
unit (5).
Installing the wheel hub
1.
Check the axle journal thread carefully for
damage.
You must never fit a wheel hub on an
axle journal with a damaged thread.
2.
Fit the O-ring (6) into the wheel hub unit (5).
3.
Apply a thin and even layer of the prescribed
lubricant to the axle journal, see "Technical
data".
Note:
Do not overlubricate the axle journal. While
fitting the wheel hub unit, the excess grease
will collect at the backside of the wheel hub.
When the vehicle is used in daily operation,
this anti-corrosion agent can leak out so that
it looks as if the oil seal leaks.
5
A
A8 00 411
6
A8 00 412
}
A8 00 344
TRAILING AXLES
2-6
©
200424
Removal and installation
8
ΧΦ65/75/85 series
8
4.
Install the guide sleeve (A), which is part of
the special tool set (DAF no. 1329496), on
the axle journal.
5.
Attach the wheel hub unit (5) securely to a
movable lifting device.
6.
Position the wheel hub unit (5) exactly in
front of the axle journal using the movable
lifting device. Slide the wheel hub unit (5) on
the axle journal.
Take care that the wheel hub unit (5) does
not rest on the guide bush as the latter is not
strong enough to take the weight of the
wheel hub unit (5).
7.
Fit the thrust washer (4).
8.
Replace the hub nut (3). Apply a few drops of
oil to the abutting surface of the hub nut (3).
Fit the hub nut (3).
9.
Fit the hub nut (3) using the hub nut wrench
(A), which is part of the special tool set
(DAF no. 1329496) and a torque amplifier.
Tighten the hub nut (3) in the specified
manner using a torque amplifier, see
"Technical data".
10. Thoroughly clean the sealing surfaces of the
wheel hub and the hub cap.
11. Apply a sealant to one of the sealing
surfaces.
12. Fit the hub cap.
13. Fit the brake calliper.
14. Put the wheels back on.
A
A8 00 343
3
4
5
A8 00 413
A
A8 00 405
©
200424
2-7
Removal and installation
TRAILING AXLES
ΧΦ65/75/85 series
8
8
2.3 REMOVAL AND INSTALLATION, TRAILING AXLE
Removing the trailing axle
1.
Remove the wheels from the trailing axle.
2.
Loosen the shock absorbers at the top and
depress these as far as possible.
3.
Remove the brake pipes and the cabling of
the disc brakes.
4.
(Temporarily) fit the outer wheels of the
trailing axle.
5.
Lower the trailing axle.
6.
Safely lift the chassis rear until the
attachment bolts holding the bearing
supports to the chassis can be removed.
7.
Remove the attachment bolts holding the
bearing supports to the chassis.
8.
Lift the chassis until the bearing supports are
clear of the chassis and the bottom pins of
the shackles are within reach.
9.
Place a wooden block right and left between
the chassis member and the axle housing of
the driven axle.
10. Place suitable supports under the yokes
where the shackle is attached.
11. Remove the lower pins from the shackles.
A8 00 408
A8 00 409
TRAILING AXLES
2-8
©
200424
Removal and installation
8
ΧΦ65/75/85 series
8
12. Insert a solid piece of pipe through the eye of
every yoke.
13. Position a trolley jack in the middle of the
pipe, supporting it.
14. Remove the supports and slowly lower the
pipe and the yokes.
15. Roll the trailing axle from under the chassis.
16. Slowly lower the chassis onto the wooden
blocks.
17. Take the rings out of the eyes of the yokes if
necessary.
Installing the trailing axle
1.
Fit the rings in the eyes of the yokes.
2.
Raise the chassis. Support the chassis in a
safe way.
3.
Insert a solid piece of pipe through the eye of
every yoke.
4.
Move the trailing axle under the chassis
using a trolley jack. Align the trailing axle and
the chassis.
A8 00 406
A800208
A8 00 406
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст