DAF CF65, CF75, CF85 Series . Manual — part 1058
©
200424
2-1
Removal and installation
TRAILING AXLES
ΧΦ65/75/85 series
8
8
2. REMOVAL AND INSTALLATION
2.1 REMOVAL AND INSTALLATION, WHEEL HUB UNIT (09N075 TRAILING
AXLE)
Removing the wheel hub unit (09N075 trailing
axle)
1.
Lift the trailing axle and support it properly.
2.
Remove the wheel.
3.
Remove the brake calliper.
4.
Remove the hub cap (2).
6
5
2
1
4
3
7
9
8
A8 00 404
TRAILING AXLES
2-2
©
200424
Removal and installation
8
ΧΦ65/75/85 series
8
5.
Remove the hub nut (4) using the special tool
set (DAF no. 1329496).
Fit the socket wrench (A) to the hub nut. Fit
the socket wrench guide (B) to the wheel hub
unit using four wheel studs. Loosen the nut
using a torque amplifier.
6.
Remove the thrust washer (5).
7.
Install the guide sleeve (A), which is part of
the special tool set (DAF no. 1329496), on
the axle journal.
8.
Remove the wheel hub unit (6) using a lifting
device. Take care that the wheel hub unit
does not rest on the guide bush (A) as the
latter is not strong enough to take the weight
of the wheel hub unit.
Installing the wheel hub unit
1.
Check the axle journal thread carefully for
damage.
You must never fit a wheel hub unit
on an axle journal with a damaged
thread.
2.
Apply a thin and even layer of the prescribed
lubricant to the entire circumference of the
axle journal, see "Technical data".
Note:
Do not overlubricate the axle journal. While
fitting the wheel hub unit, the excess grease
will collect at the backside of the wheel hub.
When the vehicle is used in daily operation,
this can leak out so that the seal wrongly
appears to be leaking.
A
B
S7 00 641
S7 00 580
A
}
S7 00 547
©
200424
2-3
Removal and installation
TRAILING AXLES
ΧΦ65/75/85 series
8
8
3.
Install the guide sleeve (A), which is part of
the special tool set (DAF no. 1329496), on
the axle journal.
4.
Position the wheel hub unit (6) precisely in
front of the axle journal using a lifting device.
Slide the wheel hub unit (6) onto the axle
journal without twisting it. Take care that the
wheel hub unit does not rest on the guide
bush (A) as the latter is not strong enough to
take the weight of the wheel hub unit.
5.
Fit the thrust washer (5).
6.
Replace the hub nut (4). Apply a few drops of
oil to the abutting surface of the hub nut. Fit
the hub nut.
7.
Fit the hub nut (4) using the special tool set
(DAF no. 1329496).
Fit the socket wrench (A) to the hub nut. Fit
the socket wrench guide (B) to the wheel hub
unit using four nuts. Tighten the hub nut (4)
in the specified manner using a torque
amplifier, see "Technical data".
8.
Fit a new O-ring (3) to the hub cap (2).
9.
Fit the brake calliper.
10. Fit the wheel.
A
S7 00 561
6
5
2
1
4
3
S7 00 581
A
B
S7 00 641
TRAILING AXLES
2-4
©
200424
Removal and installation
8
ΧΦ65/75/85 series
8
2.2 REMOVAL AND INSTALLATION, WHEEL HUB (09N220 TRAILING AXLE)
Removing the wheel hub (09N220 trailing
axle)
1.
Remove the attachment bolts (1) from the
hub cap (2) and remove the cap.
2.
Lift the trailing axle and support it properly.
3.
Remove the wheel.
4.
Remove the brake calliper.
5.
Remove the hub nut (3) using the hub nut
wrench (A), which is part of the special tool
set (DAF no. 1329496). Loosen the hub nut
(3), using a torque amplifier to do so.
6.
Remove the thrust washer (4).
3
2
1
4
5
6
7
8
9
A8 00 403
A
A8 00 405
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст