DAF CF65, CF75, CF85 Series . Manual — part 1051
©
200424
3-1
Removal and installation
TANDEM REAR AXLE 1355T
ΧΦ65/75/85 series
8
7
3. REMOVAL AND INSTALLATION
3.1 REMOVAL AND INSTALLATION, ENTIRE REAR AXLE
Removing the entire rear axle
1.
Block the front wheels using chocks.
2.
Slacken the central bolt of the spring-brake
cylinder as much as possible.
3.
Apply the parking brake.
4.
Remove the air pipes and wiring.
5.
Remove the prop shaft from the drive flange.
6.
Loosen the shock absorbers on the bottom.
7.
Loosen the control rod of the ALR valve.
8.
Support the vehicle securely with stands
under the chassis side members.
9.
Remove the axle suspension/guide.
Take precautionary measures to make sure
that the axle does not tilt during removal of
the axle suspension/guide.
10. If possible, the entire rear axle with wheels
should be rolled from under the vehicle.
Installing the entire rear axle
1.
Install the entire rear axle with wheels under
the vehicle.
2.
Fit the axle suspension/guide.
Make sure that the torque-rod supports are
fitted so that arrow A on the support points in
the driving direction.
3.
Fit the control rod of the ALR valve.
Note:
Check the setting of the ALR valve following
installation of the rear axle.
4.
Fit the shock absorbers (if applicable).
5.
Fit the prop shaft to the drive flange.
6.
Connect the electrical wiring and fit the air
pipes.
7.
Tighten the central bolt of the spring-brake
cylinder.
A
A800045
TANDEM REAR AXLE 1355T
3-2
©
200424
Removal and installation
7
ΧΦ65/75/85 series
8
3.2 REMOVAL AND INSTALLATION, AXLE SHAFTS
Removing axle shafts
1.
Jack up the rear axle and support the axle on
stands.
2.
Activate the differential lock and install the
special tool (DAF no. 0694836) at the
position of the switch.
3.
Drain the hub oil. See "Draining and filling".
4.
Remove the attachment bolts from the hub
cap and remove the hub cap.
5.
Pull the axle shaft from the wheel hub.
A800046
A800289
©
200424
3-3
Removal and installation
TANDEM REAR AXLE 1355T
ΧΦ65/75/85 series
8
7
Installing axle shafts
1.
Fit the axle shaft into the wheel hub.
2.
Turn the planet-gear shafts so that the flat
sides point outward.
3.
Check the O-ring in the hub cap. If
necessary, replace the O-ring and apply
silicone grease.
4.
Check the O-ring in the hub cap. If
necessary, replace the O-ring. Apply silicone
grease to the O-ring.
5.
Install the spring assembly. Tighten the
attachment bolts to the specified torque. See
"Technical data".
6.
Fill the hub with oil. See "Draining and filling".
7.
Remove the special tool from the differential
lock and fit the switch again.
A800040
A800046
TANDEM REAR AXLE 1355T
3-4
©
200424
Removal and installation
7
ΧΦ65/75/85 series
8
3.3 REMOVAL AND INSTALLATION, WHEEL HUB
Removing the wheel hub
1.
Jack up the rear axle and support the axle on
stands.
2.
Remove the wheels.
3.
Release the brakes and remove the brake
drum.
4.
Mark the hub at the semicircular hole in the
cover.
5.
Drain the oil. See "Draining and filling".
6.
Remove the hub cap.
7.
Remove the axle shaft.
8.
Remove the attachment nuts and tapered
spring washers.
Remove the planet-gear set from the hub
using three jacking screws.
Note:
Make sure that the planet-gear set is put
down with the circlips facing upward. This
will prevent the pins from falling out.
9.
Remove the thrust washer from the axle
journal.
10. Remove the attachment bolts from the
locking plate and remove the locking plate.
A800290
A800107
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст