DAF CF65, CF75, CF85 Series . Manual — part 1125
©
200518
3-9
Inspection and adjustment
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
ΧΦ65/65 (II) series
5
3.9 CHECKING THE POLY V-BELT
1.
Check the poly-V-belt for damage and signs
of serious wear.
2.
Check the pulleys for damage, rust and
grease deposits.
Clean or replace the belt pulleys if
necessary.
Note:
Pay special attention to the plastic pulleys and
the water pump pulley.
Dirt can be scraped off the pulleys quite easily.
Take care not to damage the pulleys.
G000374
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
3-10
©
200518
Inspection and adjustment
5
ΧΦ65/65 (II) series
3.10 CHECKING THE COOLANT FREEZING POINT
When the coolant is hot, there is an
overpressure in the cooling system.
Carefully remove the filler cap to
release the overpressure.
Do not remove the filler cap when the
engine is running.
Coolant is a toxic fluid. Contact with
the skin should therefore be
avoided.
In the event of contact with the skin:
remove with paper or a cloth, wash
with soap and water. If irritation
persists, consult a doctor.
If swallowed: DO NOT induce
vomiting. Rinse mouth, drink two
glasses of water and consult a
doctor.
In the event of inhalation: get some
fresh air and rest.
In order to avoid damaging the
cylinder block, do not top up a warm
engine with coolant.
1.
Check the anti-freeze content of the coolant.
Fill the cooling system with anti-freeze, if this
has not been done yet. Always use only
coolants that meet DAF specifications.
2.
Consult the manufacturer’s instructions for
the correct anti-freeze mixing ratio.
Preferably, use 40% anti-freeze on an
ethylene glycol base. At this percentage, not
only good frost protection, but also good
corrosion protection is guaranteed.
}
%
O
o
M2016
C
100
0
90
10
80
20
70
30
60
40
50
50
40
60
30
70
20
80
10
90
-80
-70
-60
-50
-40
-30
-20
0
-10
0
100
2
H
Ethyleenglycol
©
200518
3-11
Inspection and adjustment
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
ΧΦ65/65 (II) series
5
3.11 CHECKING FOR FUEL LEAKS
1.
Visually inspect all hose connections and
fuel system components for leaks.
3.12 CHECKING THE COMPONENTS AND HOSE CONNECTIONS FOR LEAKS
1.
Check all hose connections and cooling
system components for leaks.
2.
Check the hose connections and inlet
system components.
3.13 CHECKING THE EXHAUST SYSTEM
1.
Visually inspect the exhaust system for
leaks.
2.
Check the exhaust suspension points.
3.
Check that no heat transfer (due to
accumulated dirt, for example) can take
place to the exhaust system area, such as
pipes, components etc.
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
3-12
©
200518
Inspection and adjustment
5
ΧΦ65/65 (II) series
3.14 CHECKING THE RADIATOR AND INTERCOOLER FOR FOULING
1.
Visually inspect the radiator and intercooler
for fouling If necessary, clean the radiator
and intercooler, see "Cleaning".
3.15 CHECKING THE AIR INLET DUST TRAPPING VALVE
1.
Check the condition of the rubber valves.
Steering gear and brake system
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст