DAF CF65, CF75, CF85 Series . Manual — part 1104
©
200448
3-15
Removal and installation
LEAF SUSPENSION
ΧΦ65/75/85 series
9
5
3.9 REMOVAL AND INSTALLATION, TANDEM AXLE SPRING ASSEMBLY
Support the vehicle securely and
work safely.
Removing tandem axle spring assembly
1.
Support both axles and remove the wheels.
2.
Jack up the chassis under the central
suspension.
3.
Loosen the nuts (1) of the tie rods (4) until the
centre bolt comes off the pivot pin shackle.
4.
Lower the chassis until the spring assembly
rests on wearing plates (2).
5.
Remove the tie rods (4) and the bottom
spring plate (3). The spring assembly is now
ready to be taken off.
Before the spring assembly of a
trapezoidal leaf spring assembly is
taken off, it must be turned upside-
down. If this is not done, the spring
assembly will tip over when being
removed.
6.
Turn the spring assembly of a trapezoidal
leaf spring assembly upside-down. Remove
the spring assembly.
}
1
3
4
1
2
W904017
W904021
}
LEAF SUSPENSION
3-16
©
200448
Removal and installation
5
ΧΦ65/75/85 series
9
Installing tandem axle spring assembly
1.
Put the spring assembly on the brake drums.
Turn the spring assembly of a trapezoidal
leaf spring assembly right side up again, so
that the short side is on top.
2.
Put the spring assembly side by side on the
wearing plates. This will prevent the
trapezoidal leaf spring assembly from tipping
over.
3.
Fit the tie rods (4) and the spring plate (3).
When tightening, check that the centre bolt
head is located in the recess of the bearing
support and that the alignment plates fit onto
the cams of the bearing support.
4.
Lower the chassis.
5.
Tighten the tie rods (4) to the specified
torque. See "Technical data".
Make sure that the attachment nuts fully
engage the tie rod.
6.
Apply grease to the threaded ends of the tie
rods sticking out above the attachment nuts.
7.
Put the wheels back on.
8.
Re-torque the tie rod nuts after 2,500 km.
W904023
1
3
4
1
2
W904017
©
200448
3-17
Removal and installation
LEAF SUSPENSION
ΧΦ65/75/85 series
9
5
3.10 REMOVAL AND INSTALLATION, PIVOT PIN
Removing pivot pin
1.
Remove the spring assembly.
2.
Remove the pivot pin cover (15) and collect
the oil.
3.
Remove the O-ring (14).
4.
Remove the two attachment bolts (13) from
the locking plate (11).
5.
Remove the locking plate (11).
6.
Take bearing support (10) off the pivot
pin (2).
7.
Take the oil seal (6) out of the bearing
support (10).
8.
Remove the bearing bushes (7) and (8) from
the bearing support (10), using a suitable
driver.
1
2
4
5
9
3
6
7
8
10
11
14
15
17
16
19
18
13
12
W9 04 025
LEAF SUSPENSION
3-18
©
200448
Removal and installation
5
ΧΦ65/75/85 series
9
9.
Remove the attachment bolts (9) from the
pivot pin flange (5) and use a puller to pull the
pivot pin flange together with the pivot pin (2)
out of the chassis.
10. Drive the pivot pin (2) out of the pivot pin
flange (5).
Installing pivot pin
1.
Check the oil seal chamber in the bearing
support for damage.
Check the contact face of the oil seal on the
pivot pin for damage.
2.
Drive the pivot pin (2) out of the pivot pin
flange (5).
3.
Apply a thin layer of grease to surfaces (A) of
pivot pin (2) and the pivot pin flange (5) and
reinstall them in the chassis.
4.
Fit the attachment bolts of the pivot pin
flange crosswise and tighten them to the
specified tightening torque, see "Technical
data".
W9 04 030
17 15 14
10
5
4
A
A
13 19
11
8
7
6
2
B
6mm
6mm
W9 04 035
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст