DAF CF65, CF75, CF85 Series . Manual — part 1065
©
200424
2-9
General
HYDRAULIC LIFTING GEAR
ΧΦ65/75/85 series
8
9
2.7 OVERVIEW DRAWING, CYLINDER
1 2
1
2
11 12
13 14 15 16 17 18
3 4 5 6
8 9
A
B
10
7
A8 00 248
1.
Circlip
2.
Bearing
3.
Dirt scraper
4.
Circlip
5.
O-ring
6.
Spring clip
7.
Sealing ring
8.
Plastic ring
9.
O-ring
10.
Piston-rod guide
11.
Piston rod
12.
Cylinder
13.
Piston
14.
Plastic ring
15.
Sealing ring
16
O-ring
17.
Plastic ring
18.
Nut
A
Pipe connection
B
Pipe connection
HYDRAULIC LIFTING GEAR
2-10
©
200424
General
9
ΧΦ65/75/85 series
8
©
200424
3-1
Inspection and adjustment
HYDRAULIC LIFTING GEAR
ΧΦ65/75/85 series
8
9
3. INSPECTION AND ADJUSTMENT
3.1 CHECKING THE SYSTEM PRESSURE AND PRESSURE SWITCH
1.
Make sure that the trailing axle wheels are
fully lowered and on the ground.
2.
Connect the pressure gauge, special tool
(DAF no. 0535653) to the pipe which is
connected to pipe connection B by a T-piece
(M16 x 1.5).
3.
Lift the trailing axle and take the pressure
reading. Compare the reading with the
technical data. See "Technical data".
The pressure switch cannot be adjusted. If
the value deviates, the pressure switch
should be replaced.
4.
Lower the trailing axle and remove the T-
piece and the pressure gauge.
5.
Check the oil level in the reservoir and top up
if necessary.
A8
00 278
HYDRAULIC LIFTING GEAR
3-2
©
200424
Inspection and adjustment
9
ΧΦ65/75/85 series
8
3.2 INSPECTION AND ADJUSTMENT, PRESSURE RELIEF VALVE
Checking the pressure relief valve
1.
Make sure that the trailing axle wheels are
fully lowered and on the ground.
2.
Connect the pressure gauge, special tool
(DAF no. 0535653) to the pipe which is
connected to pipe connection B by a T-piece
(M16 x 1.5).
3.
Detach the pressure switch connector.
4.
Lift the trailing axle and take the pressure
reading. Release the control switch on the
dashboard immediately once the maximum
pressure is achieved.
Note:
If the pressure exceeds 200 bar, the control
switch on the dashboard should be released
immediately.
5.
Compare the reading with the technical data.
See "Technical data". Adjust the pressure
relief valve if the value deviates.
6.
Fit the pressure switch connector.
7.
Lower the trailing axle and remove the T-
piece and the pressure gauge.
8.
Check the oil level in the reservoir and top up
if necessary.
Adjusting the pressure relief valve
1.
Make sure that the trailing axle wheels are
fully lowered and on the ground.
2.
Connect the pressure gauge, special tool
(DAF no. 0535653) to the pipe which is
connected to pipe connection‚ B by a T-piece
(M16 x 1.5).
3.
Detach the pressure switch connector.
4.
Loosen the lock nut (2) of the pressure relief
valve (3).
B
A
A8 00 281
A8 00 280
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст