DAF CF65, CF75, CF85 Series . Manual — part 1007
©
200424
3-1
Single rear axle 1347
TECHNICAL DATA
ΧΦ65/75/85 series
8
0
3. SINGLE REAR AXLE 1347
3.1 GENERAL
Sealant for differential
Sealant for axle shaft
Wheel speed sensor ring
(1) With a lowered trailing axle
Trailing axle lifting height
Mating surface and around bolt holes of axle
body
Loctite 5910
Mating surface of axle shaft flange
Loctite 5910
Axial end play
maximum 0.25 mm
Driven axle caster
FAG
3,5
FAS (11/7 ratio)
(1)
4
FAS (10/10 ratio)
(1)
3,5
Other
4,5
Leaf-sprung trailing axle lifting height
100 mm min.
Installation of wheel hub unit
Axle journal for installing the wheel hub unit
treated with
Gleitmo 805
TECHNICAL DATA
3-2
©
200424
Single rear axle 1347
0
ΧΦ65/75/85 series
8
3.2 TIGHTENING TORQUES
The tightening torques stated in this section are
different from the standard tightening torques
stated in the overview of the standard tightening
torques. The other threaded connections not
specified must therefore be tightened to the
torque stated in the overview of standard
tightening torques.
When attachment bolts and nuts are replaced, it
is important that - unless stated otherwise - these
bolts and nuts are of exactly the same length and
property class as those removed.
Differential gear
(1) Use Loctite 262 to secure
(2) Apply Loctite 572
Hub
(1) Only fit a new hub nut
3.3 FILLING CAPACITIES
Drive flange attachment nut
1250 Nm
(1)
Differential lock cover attachment bolts
30 Nm
Attachment bolts differential to axle housing
260 Nm
(2)
Torx plug (level check/filler and drain plug)
85 Nm
Hub nut
(1)
1
st
phase
500 Nm
2
nd
phase rpm
turn the hub 10 revolutions at a speed of
approx. 40 rpm
3
rd
phase
550 Nm
4
th
phase rpm
turn the hub 10 revolutions at a speed of
approx. 40 rpm
5
th
phase
1300 Nm
Axle shaft attachment bolts
260 Nm
Differential
Minimum caster
Maximum caster
Filling capacity
approx. 21.5 litres
approx. 23.5 litres
©
200424
4-1
Single rear axle 1354
TECHNICAL DATA
ΧΦ65/75/85 series
8
0
4. SINGLE REAR AXLE 1354
4.1 GENERAL
Sealant for differential
Wheel bearings
(1) Measured at the circumference of the hub
Wheel speed sensor ring
(1) With a lowered trailing axle
Trailing axle lifting height
Studs from axle housing
Mating face and around stud bolts of banjo
housing
Loctite 5910
Wheel bearings pre-load:
frictional force without hub seal
30 - 62 N
(1)
Axial end play
maximum 0.25 mm
Driven axle caster
FAG
3,5
FAS (11/7 ratio)
(1)
4,0
FAS (10/10 ratio)
(1)
3,5
Other
4,5
Leaf-sprung trailing axle lifting height
100 mm min.
Fit studs with locking compound
Loctite 243
TECHNICAL DATA
4-2
©
200424
Single rear axle 1354
0
ΧΦ65/75/85 series
8
4.2 TIGHTENING TORQUES
The tightening torques stated in this section are
different from the standard tightening torques
stated in the overview of the standard tightening
torques. The other threaded connections not
specified must therefore be tightened to the
torque stated in the overview of standard
tightening torques.
When attachment bolts and nuts are replaced, it
is important that - unless stated otherwise - these
bolts and nuts are of exactly the same length and
property class as those removed.
Differential
(1) Use Loctite 262 to secure
Hub
(1) Use Loctite 243 to secure
4.3 FILLING CAPACITIES
Differential
Hub
Drive flange attachment nut
1325 Nm
(1)
Locking nut of differential-lock cylinder
80 Nm
Attachment nuts differential to axle housing
260 Nm
Torx plug (level check/filler and drain plug)
85 Nm
Hub nut
2125 Nm
Locking plate attachment bolts
30 Nm
(1)
Planet wheel attachment bolts
45 Nm
Hub cap attachment bolts
30 Nm
Torx plug (level check/filler and drain plug)
85 Nm
Filling capacities
approx. 16.5 litres
Oil capacity, per hub
2.0 litres
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст