DAF CF65, CF75, CF85 Series . Manual — part 1006

©

200424

1-1

Single rear axle 1132

TECHNICAL DATA

ΧΦ65/75/85 series

8

0

1. SINGLE REAR AXLE 1132

1.1 GENERAL

Sealant for differential

Sealant for axle shaft

Wheel speed sensor ring

Installation of wheel hub unit

Driven axle caster

Mating surface and around bolt holes of axle

body

Loctite 5910

Mating surface of axle shaft flange

Loctite 5910

Axial end play

maximum 0.25 mm

Axle journal for installing the wheel hub unit treat-

ed with

Gleitmo 805

FA model

4,5



TECHNICAL DATA

1-2

©

200424

Single rear axle 1132

0

ΧΦ65/75/85 series

8

1.2 TIGHTENING TORQUES

The tightening torques stated in this section are

different from the standard tightening torques

stated in the overview of the standard tightening

torques. The other threaded connections not

specified must therefore be tightened to the

torque stated in the overview of standard

tightening torques.

When attachment bolts and nuts are replaced, it

is important that - unless stated otherwise - these

bolts and nuts are of exactly the same length and

property class as those removed.

Differential

(1) Use Loctite 262 to secure

(2) Apply Loctite 572

Hub

(1) Only fit a new hub nut

1.3 FILLING CAPACITIES

Drive flange attachment nut

1250 Nm

(1)

Differential lock cover attachment bolts

30 Nm

Attachment bolts differential to axle housing

170 Nm

(2)

Torx plug (level check/filler and drain plug)

85 Nm

Hub nut

(1)

1

st

phase

500 Nm

2

nd

phase

turn the hub 10 revolutions at a speed of

approx. 40 rpm

3

rd

phase

550 Nm

4

th

phase

turn the hub 10 revolutions at a speed of

approx. 40 rpm

5

th

phase

1300 Nm

Axle shaft attachment bolts

260 Nm

Differential

Minimum caster

Maximum caster

Filling capacity

approx. 15.0 litres

approx. 17.5 litres

©

200424

2-1

Single rear axle 1339

TECHNICAL DATA

ΧΦ65/75/85 series

8

0

2. SINGLE REAR AXLE 1339

2.1 GENERAL

Sealant for differential

Sealant for axle shaft

Wheel speed sensor ring

(1) With a lowered trailing axle

Trailing axle lifting height

Installation of wheel hub unit

Mating surface and around bolt holes of axle

body

Loctite 5910

Mating surface of axle shaft flange

Loctite 5910

Axial end play

maximum 0.25 mm

Driven axle caster
FAG

3,5



FAS (11/7 ratio)

(1)

4



FAS (10/10 ratio)

(1)

3,5



Other

4,5



Leaf-sprung trailing axle lifting height

100 mm min.

Axle journal for installing the wheel hub unit

treated with

Gleitmo 805

TECHNICAL DATA

2-2

©

200424

Single rear axle 1339

0

ΧΦ65/75/85 series

8

2.2 TIGHTENING TORQUES

The tightening torques stated in this section are

different from the standard tightening torques

stated in the overview of the standard tightening

torques. The other threaded connections not

specified must therefore be tightened to the

torque stated in the overview of standard

tightening torques.

When attachment bolts and nuts are replaced, it

is important that - unless stated otherwise - these

bolts and nuts are of exactly the same length and

property class as those removed.

Differential

(1) Use Loctite 262 to secure

(2) Apply Loctite 572

Hub

(1) Only fit a new hub nut

2.3 FILLING CAPACITIES

Drive flange attachment nut

1250 Nm

(1)

Differential lock cover attachment bolts

30 Nm

Attachment bolts differential to axle housing

260 Nm

(2)

Torx plug (level check/filler and drain plug)

85 Nm

Hub nut

(1)

1

st

phase

500 Nm

2

nd

phase rpm

turn the hub 10 revolutions at a speed of

approx. 40 rpm

3

rd

phase

550 Nm

4

th

phase rpm

turn the hub 10 revolutions at a speed of

approx. 40 rpm

5

th

phase

1300 Nm

Axle shaft attachment bolts

260 Nm

Differential

Minimum caster

Maximum caster

Filling capacity

approx. 18.0 litres

approx. 20.0 litres