DAF CF65, CF75, CF85 Series . Manual — part 1073
©
200424
2-1
Inspection and adjustment
09N044 LEADING REAR AXLE (FTP VEHICLE)
ΧΦ65/75/85 series
8
10
2. INSPECTION AND ADJUSTMENT
2.1 INSPECTION AND ADJUSTMENT, WHEEL BEARING PLAY, 09N044
LEADING REAR AXLE
Checking the wheel bearing play
1.
Remove the hub cap using special tool
(DAF no. 1329498).
2.
Lift the leading rear axle and support it
properly.
3.
Release the brakes.
4.
Fit a dial gauge; let the stylus rest against the
axle journal.
5.
Push and pull on the wheel. Read the value
off the gauge. Compare this reading to the
specified value. See "Technical data". If the
reading falls outside the tolerance range, the
wheel bearing play should be re-adjusted.
6.
Fit the hub cap. Tighten the hub cap to the
specified torque using the special tool
(DAF no. 1329498), see "Technical data"'.
7.
Adjust the brakes.
Adjusting the wheel bearing play
1.
Remove the hub cap (4) using special tool
(DAF no. 1329498).
2.
Lift the leading rear axle.
3.
Release the brakes.
4.
Remove the split pin (3) from the hub nut (2).
5.
Tighten the hub nut to the specified
tightening torque, see "Technical data". Turn
the wheel at least 5 revolutions in anti-
clockwise direction and then 5 revolutions in
clockwise direction when fixing the hub nut.
6.
Check that the wheel rotates smoothly.
7.
Turn back the hub nut until the split pin can
be fitted. Fit a new split pin.
S7 00 635
S7 00 657
1
2
3
4
09N044 LEADING REAR AXLE (FTP VEHICLE)
2-2
©
200424
Inspection and adjustment
10
ΧΦ65/75/85 series
8
Note:
There are 2 split pin holes in the axle journal.
Select the split pin hole where the hub nut needs
to be turned back the smallest distance.
8.
Check the wheel bearing play. Check the
bearings for wear if the wheel bearing play
remains too large after adjustment.
9.
Fit the hub cap. Tighten the hub cap to the
specified torque using the special tool
(DAF no. 1329498), see "Technical data"'.
10. Adjust the brakes.
2.2 CHECKING THE HUB AND WHEEL BEARINGS
1.
Inspect the bearings for damage at the
following points:
-
the roller bearing race,
-
the bearing cage,
-
the raceways of the inner and outer
race.
If damage is found, the entire bearing (inner
race/bearing cage and outer race) should be
replaced.
2.
If the outer race of the bearing is loose in the
hub or has turned in the hub, the hub should
be replaced.
3.
Check the axle journal screw thread, the
bearing surfaces of the inner bearing races
and the running surface of the seal for
damage.
©
200424
3-1
Removal and installation
09N044 LEADING REAR AXLE (FTP VEHICLE)
ΧΦ65/75/85 series
8
10
3. REMOVAL AND INSTALLATION
3.1 REMOVAL AND INSTALLATION, WHEEL HUB
Removing the wheel hub
1.
Remove the hub cap (5) using special tool
(DAF no. 1329498).
2.
Lift the leading rear axle and support it
properly.
3.
Remove the split pin (4) and the hub nut (3).
4.
Remove the outer wheel bearing (2).
5.
Remove the hub (1) with the wheel.
Installing the wheel hub
1.
Remove the grease from the hub (1).
2.
Clean the bearings and liberally re-grease
the outer bearing races and bearing cages.
3.
Lubricate the space between the wheel
bearings with new grease.
4.
Install the hub with the wheel.
5.
Fit the outer wheel bearing (2).
6.
Fit the hub nut (5).
7.
Adjust the wheel bearing play, see chapter
"Inspection and adjustment".
8.
Fit a new split pin (4).
9.
Lower the leading rear axle.
10. Fit the hub cap (5) using special tool
(DAF no. 1329894). Tighten the hub cap to
the specified torque, see "Technical data".
11. Adjust the brakes.
A8 00 430
1
2
3 4
5
09N044 LEADING REAR AXLE (FTP VEHICLE)
3-2
©
200424
Removal and installation
10
ΧΦ65/75/85 series
8
3.2 REMOVAL AND INSTALLATION, HUB SEAL
Removing the hub seal
1.
Remove the wheel hub from the axle journal.
2.
Drill two small holes into the seal and screw
the special tool (B) (DAF no. 0484899) into
the seal. Pull the oil seal from the wheel hub
using the special tool (A)
(DAF no. 0694928).
Installing the hub seal
1.
Check the seal chamber for damage.
2.
Use the special tool (DAF no. 1329497) to
install the seal. Press the seal into the hub.
3.
Apply a little grease to the lips of the seal.
4.
Install the wheel hub on the axle journal.
A
B
A8 00 432
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст