Honda Civic. Manual — part 244
Fig. 200: Identifying Harness Cover, Clamp & Torque Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.
7. Disconnect the A/T clutch pressure control solenoid valve C connector (A).
Fig. 201: Identifying A/T Clutch Pressure Control Solenoid Valve C
Connector
Courtesy of AMERICAN HONDA MOTOR CO., INC.
8. Measure the A/T clutch pressure control solenoid valve C resistance at the
connector terminals.
Standard: 3-10 ohms
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
If the resistance is out of standard, replace A/T clutch pressure control
solenoid valve C (see A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE B AND C REPLACEMENT ).
If the resistance is within the standard, go to step 9.
9. Connect a jumper wire from the negative battery terminal to A/T clutch
pressure control solenoid valve C connector terminal No. 2, and connect
another jumper wire from the positive battery terminal to connector terminal
No. 1.
If a clicking sound is heard, the valve is OK. Reconnect the connector, and
install all removed parts.
If no clicking sound is heard, go to step 10.
10. Remove A/T clutch pressure control solenoid valve B and C.
Fig. 202: Identifying ATF Pipe, ATF Joint Pipes, O-Rings, Gasket &
Torque Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.
11. Remove the ATF pipe (A), the ATF joint pipes (D), the O-rings (E), and the
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
gasket (F).
12. Check the fluid passage of the solenoid valve for contamination.
13. Connect a jumper wire from the negative battery terminal to A/T clutch
pressure control solenoid valve C connector terminal No. 2, and connect
another jumper wire from the positive battery terminal to connector terminal
No. 1. Make sure A/T clutch pressure control solenoid valve C moves.
Fig. 203: Checking A/T Clutch Pressure Control Solenoid Valve C
Courtesy of AMERICAN HONDA MOTOR CO., INC.
14. Disconnect one of the jumper wires and check the valve movement at the fluid
passage in the valve body mounting surface. If the valve binds or moves
sluggishly, or if the solenoid valve does not operate, replace A/T clutch
pressure control solenoid valves B and C.
15. Clean the mounting surfaces and fluid passages of the solenoid valve body and
the transmission housing.
16. Install a new gasket with the blue side down and the white side up on the
transmission housing.
17. Install the ATF pipe and the ATF joint pipes, and install new O-rings over the
ATF joint pipes.
18. Install A/T clutch pressure control solenoid valves B and C.
19. Check the A/T clutch pressure control solenoid valve B and C connectors for
rust, dirt, or oil, then connect the connectors securely.
20. Secure the harness cover with the mounting bolts, and install the harness
clamp.
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
21. Install the intake air duct and the air cleaner assembly (see AIR CLEANER
ELEMENT INSPECTION/REPLACEMENT ).
A/T CLUTCH PRESSURE CONTROL SOLENOID VALVE B AND C REPLACEMENT
1. Remove the air cleaner assembly (see AIR CLEANER ELEMENT
INSPECTION/REPLACEMENT ) and the intake air duct.
2. Remove the mounting bolts securing the harness cover (A), and remove the
harness clamp (D).
Fig. 204: Identifying Harness Cover, Clamp & Torque Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Disconnect the connectors from A/T clutch pressure control solenoid valve B
and C.
4. Remove A/T clutch pressure control solenoid valve B and C.
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст