Honda Civic. Manual — part 242
Fig. 191: Checking A/T Clutch Pressure Control Solenoid Valve A
Courtesy of AMERICAN HONDA MOTOR CO., INC.
14. Disconnect one of the jumper wires and check the valve movement at the fluid
passage in the valve body mounting surface. If the valve binds or moves
sluggishly, or if the solenoid valve does not operate, replace A/T clutch
pressure control solenoid valve A.
15. Clean the mounting surfaces and fluid passages of the solenoid valve body and
the transmission housing.
16. Install a new gasket with the blue side down and the white side up on the
transmission housing, and install the ATF pipe and the ATF joint pipes.
17. Install new O-rings over the ATF joint pipes.
18. Install A/T clutch pressure control solenoid valve A.
19. Check the connectors for rust, dirt, or oil, clean or repair if necessary, then
connect the connectors securely.
20. Secure the harness cover with the mounting bolts, and install the harness
clamp.
21. Install the intake air duct and the air cleaner assembly (see AIR CLEANER
REMOVAL/INSTALLATION )
A/T CLUTCH PRESSURE CONTROL SOLENOID VALVE A REPLACEMENT
1. Remove the air cleaner assembly (see AIR CLEANER ELEMENT
INSPECTION/REPLACEMENT ) and the intake air duct.
2. Remove the mounting bolts securing the harness cover (A), and remove the
harness clamp (B).
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
Fig. 192: Identifying Harness Cover, Harness Clamp & Torque
Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Disconnect the A/T clutch pressure control solenoid valve A connector.
4. Remove the mounting bolts and A/T clutch pressure control solenoid valve A.
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
Fig. 193: Identifying ATF Pipe, ATF Joint Pipes, O-Rings, Gasket &
Torque Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Remove the ATF pipe (B), the ATF joint pipes (C), the O-rings (D), and the
gasket (E).
6. Check the fluid passage of the transmission housing for dust or dirt, and clean
the passage.
7. Install a new gasket with the blue side down and the white side up on the
transmission housing, and install the ATF pipe and the ATF joint pipes.
8. Install new O-rings over the ATF joint pipes.
9. Install a new A/T clutch pressure control solenoid valve A.
10. Check the A/T clutch pressure control solenoid valve A connector for rust, dirt,
or oil, then connect the connector securely.
11. Secure the harness cover with the mounting bolts, and install the harness
clamp.
12. Install the intake air duct and the air cleaner assembly (see AIR CLEANER
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
ELEMENT INSPECTION/REPLACEMENT )
A/T CLUTCH PRESSURE CONTROL SOLENOID VALVE B TEST
1. Connect the HDS to the DLC (A) located behind the driver's dashboard lower
cover.
Fig. 194: Identifying Data Link Connector
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Turn the ignition switch to ON (II). Make sure the HDS communicates with
the PCM. If it does not, go to the DLC circuit troubleshooting (see DLC
CIRCUIT TROUBLESHOOTING ).
3. Select Clutch Pressure Control (Linear) Solenoid Valve B in the Miscellaneous
Test Menu with the HDS.
4. Test A/T clutch pressure control solenoid valve B with the HDS.
If the valve tests OK, the test is complete. Disconnect the HDS.
If the valve does not test OK, follow the instructions on the HDS.
If the valve does not test OK, and the HDS does not determine the cause,
go to step 5.
5. Remove the air cleaner assembly (see AIR CLEANER ELEMENT
INSPECTION/REPLACEMENT ) and the intake air duct.
6. Remove the mounting bolts securing the harness cover (A), and remove the
harness clamp (B).
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст